Product Specification

Why Can a Pneumatic Clamp Still Fail to Fit an Aluminum Profile Even When the Maximum Opening Is Large Enough?

Problem | Why Is Maximum Opening Not Enough?

When selecting a pneumatic clamp for aluminum profiles, many users first check one specification: maximum opening.

This is useful, but it is not enough.

For example, the KRT-110 has a 90 mm maximum opening. If an aluminum profile is listed as 70 mm or 80 mm wide, it may appear that the clamp will automatically fit.

In practice, compatibility depends on more than nominal width.

The real questions are:

• What is the width at the actual clamping point?
• What is the clamping direction?
• Are there ribs, grooves, steps, or local protrusions?
• Is there enough clearance during initial loading?
• Is there enough installation space for the clamp?

Therefore, maximum opening should be treated as one selection parameter, not the only selection rule.

Cause | Where Does Size Mismatch Come From?

1. Nominal width is not the same as clamping width

Aluminum profiles often have complex cross-sections.

A profile listed as 80 mm wide may have a much smaller contact section, or a local protrusion that increases the required opening.

The dimension that matters most is the section where the clamp jaws actually contact the workpiece.

2. Resting opening affects initial loading

The KRT-110 has a 41.15 mm resting opening and a 90 mm maximum opening.

The difference is:

90 − 41.15 = 48.85 mm

This means the clamp does not begin in its fully open position.

If the workpiece requires more initial clearance during loading, the maximum opening alone may not solve the problem.

3. Clamping direction changes the required opening

The same profile can require different opening dimensions depending on the clamping direction.

This is why engineers should evaluate the actual clamping cross-section, not just the nominal product size.

Solution | How to Check Real Compatibility

A more reliable method is to compare clamp dimensions directly with the actual clamping position.

The confirmed KRT-110 dimensions are:

Before selection, review the profile drawing and mark the real jaw contact position.

Check the clamping-point width

Measure the dimension the jaws actually need to cross.

Check the loading path

Determine whether the workpiece can enter the clamp from the 41.15 mm resting position.

Check the maximum opening

If the required opening is close to 90 mm, additional verification of jaw position and loading motion is recommended.

Check installation space

The KRT-110 has an overall length of 112 mm.

This dimension should be compared with the available fixture or equipment space.

Application | Where Is This Problem Most Common?

This issue is especially common with:

• Irregular aluminum profiles
• Profiles with complex cross-sections
• Profiles with local ribs or raised areas
• Production lines handling multiple profile sizes

In these applications, a better selection method is to evaluate:

profile cross-section + clamping point + clamping direction + opening size

as one complete set of information.

How to Choose

Step 1: Obtain the profile cross-section drawing

Use the actual geometry, not only the product name or nominal width.

Step 2: Mark the real clamping point

Identify exactly where the jaws will contact the profile.

Step 3: Compare with the 41.15 mm resting opening

Check whether the initial loading condition is suitable.

Step 4: Compare with the 90 mm maximum opening

Confirm that the required opening stays within the clamp’s available range.

Step 5: Check the 112 mm overall length

Verify that the clamp fits within the available installation space.

FAQ

Does a 90 mm maximum opening mean every profile below 90 mm will fit?

No.

Compatibility also depends on profile geometry, clamping direction, and the actual contact section.

Why does the 41.15 mm resting opening matter?

Because it represents the clamp’s initial opening condition before reaching the maximum opening.

What is the opening difference?

The difference between 41.15 mm and 90 mm is 48.85 mm.

How should irregular profiles be evaluated?

Use a cross-section drawing, clamping direction, and actual clamping-point dimensions.

Conclusion

A large maximum opening does not automatically guarantee correct clamp matching.

For the KRT-110, the 41.15 mm resting opening, 90 mm maximum opening, and 112 mm overall length provide clear selection data. Final compatibility should be evaluated together with the actual aluminum profile geometry, clamping position, and available installation space.