Allen Bradley Modules 1761-CBL-HM02 1761CBLHM02 AB 1761 CBLH M02 PLC Cable 90

Product Specification

Allen Bradley Modules 1761-CBL-HM02 1761CBLHM02 AB 1761 CBLH M02 PLC Cable 90 Degree 50% discount quick response

Product Description:

After starting RSLogix 5000 and either starting a new project or opening an existing project, make sure
that you are OFFLINE with the ControlLogix processor. I/O configuration is only available when offline.
If you have not already defined the contents of your ControlLogix chassis under your project's "I/O
Configuration" folder, you will need to define the ControlNet bridge module at a minimum. Use the right
mouse button to click on the "I/O Configuration" folder, then choose "New Module" from the pop-up menu.From the dialog box that appears, choose the ControlNet bridge of the type (1756-CNB or 1756-CNBR)and series that you are using. In the next screen, you will need to name the ControlNet bridge and
indicate its position in the ControlLogix chassis (slot 0 is the leftmost).After defining the ControlNet bridge, use the right mouse button to click on the ControlNet bridge under"I/O configuration", then choose "New Module" from the pop-up menu

Related Product Recommendation:

Product's Character:

For the requested packet interval, enter the number of milliseconds desired between each I/O message
between the ControlLogix processor and the 1203-CN1. The 1203-CN1 can handle a packet interval as
low as 5 milliseconds; therefore, make sure that this value is set to at least Click the "Finish" button to
complete the configuration of the I/O connection in RSLogix 5000. At this point, download your configuration to the ControlLogix processor, then exit RSLogix 5000. To actually schedule the I/O, you will need to start RSNetWorx for ControlNet. Once RSNetWorx starts, go online to the ControlNet network
containing the ControlLogix chassis and 1203-CN1 being configured. Turn on the "Enable Edits" check box, then save the network. This causes the I/O connection created in RSLogix 5000 to be scheduled in the ControlLogix processor. After a few seconds, the I/O LED on the ControlLogix processor and the module LED on the 1203-CN1 should stop blinking and remain green. If they do not, it could indicate a number of I/O-related problems

1771-NR Analog Input Module AB
1771-NT1 Analog Input Module AB
1771-NT2 Analog Input Module AB
1771-OA Digital Output Module AB
1771-OAD AC Output Module AB
1771-OAN Digital Output Module AB
1771-OBD Digital Output Module AB

1771-OBN Digital Output Module AB
1771-OC Digital Output Module AB
1771-OD Digital Output Module AB
1771-OD16 Digital Output Module AB
1771-ODC Digital Output Module AB
1771-ODD Digital Output Module AB
1771-ODZ Digital Output Module AB
1771-OFE1 960578 Analog Output Module AB
1771-OFE2 Analog Output Module AB
1771-OFE3 Analog Output Module AB
1771-OG TTL Output Module AB
1771-OGD TTL Output Module AB
1771-OM Digital Output Module AB
1771-OMD AC Output Module AB
1771-ON Digital Output Module AB
1771-OP Digital Output Module AB
1771-OQ Digital Output Module AB
1771-OQ16 1771-OQ16 A Digital Output Module AB
1771-OR Digital Output Module AB
1771-OVN Digital Output Module AB
1771-OW Selectable Contact Module AB
1771-OW16 1771-0W16 B Digital Output Module AB
1771-OWN 1771-0W16 B Digital Output Module AB
1771-OWNA 1771-0W16 B Digital Output Module AB
1771-OX Output Module AB
1771-OYL Digital Output Module AB
1771-OZC Contact Output Module AB
1771-OZL Digital Output Module AB
1771-P10 Power Supply Module AB

The use of the product: