HJ AUTOMATIC CONTROL TECHNOLOGY CO., LTD
| Payment Terms | T/T, L/C |
| Supply Ability | 5 set per month |
| Delivery Time | 40 days |
| Packaging Details | Plywood |
| Product Name | Ice Water Shock Test Chamber |
| test sample | Electric And Electronic Components In Motor Vehicles |
| Temperature range | RT+10°C -160°C |
| Test fluid | de-ionized water |
| Volume of water tank | 100L |
| water flow | between 3 l and 4 l per 3 s (splash duration) |
| function | Ice water shock test, Temperature Shock With Splash Water |
| Standard | ISO16750-4, VW-80000 |
| Brand Name | HJ |
| Model Number | HJAP07 |
| Certification | Third party calibration certificate(cost additional) |
| Place of Origin | China |
View Detail Information
Explore similar products
HJ081 Automotive Fuel Tank Helium Leak Detector High-Precision Auto Parts Test
HJ-LS-6000 Automotive Heat Exchanger Helium Leak Detector High-Sensitivity Auto
IPX12 Drip Test Chamber Compliant With IEC 60529 IEC 60068 Automotive Component
Automotive Inverter Helium Leak Detection Equipment Alarm Leak Rate 1.0E-5 Mbar
Product Specification
| Payment Terms | T/T, L/C | Supply Ability | 5 set per month |
| Delivery Time | 40 days | Packaging Details | Plywood |
| Product Name | Ice Water Shock Test Chamber | test sample | Electric And Electronic Components In Motor Vehicles |
| Temperature range | RT+10°C -160°C | Test fluid | de-ionized water |
| Volume of water tank | 100L | water flow | between 3 l and 4 l per 3 s (splash duration) |
| function | Ice water shock test, Temperature Shock With Splash Water | Standard | ISO16750-4, VW-80000 |
| Brand Name | HJ | Model Number | HJAP07 |
| Certification | Third party calibration certificate(cost additional) | Place of Origin | China |
| High Light | ISO16750 Ice Water Shock Test Chamber ，ISO16750 Shock Test Chamber ，ISO16750 Ice Test Chamber | ||
Auto Parts Test Equipment ISO 16750 Ice Water Shock Test For Electronic Components
Standard:
VW-80000 Electric And Electronic Components In Motor Vehicles up to 3.5t General Requirements, Test Conditions and Tests clause 9.12 K-12 Temperature Shock With Splash Water;
ISO16750-4 Road vehicles-Environmental conditions and testing for electrical and electronic equipment-Part 4: Climatic loads clause 5.4.2 Ice water shock test.
Purpose:
This test simulates a thermal shock induced by ice water and applies to products in the splash areas of the vehicle. The purpose of this test is to simulate ice water splashing over a hot system/component. This happens when driving on wet roads during the winter. Failure modes are mechanical cracking of materials or seal failures caused by different temperature expansion coefficients. Auto Parts Test Equipment
Test method:
Splash water test:
Heat the DUT in a hot air oven at T max for the specified holding time, t h . Then splash the DUT with ice water for 3 s.
If the DUT is splashed in the vehicle from only one direction, splash it from this direction only while it is in an as-installed position. If the equipment is splashed from various directions in the vehicle, then these directions shall be taken into account. In this case, use a new DUT for each splash direction. The width of the splash directed at the DUT shall always be greater than the width of the DUT. If the DUTs to be splashed prove too big for one jet, arrange several jets in a row to produce a line of splash impact on the DUT. See Figures 4 to 6.
Test parameters include:
⎯ number of cycles: 100;
⎯ holding time, t h , at T max : 1 h or until DUT temperature stabilization is reached;
⎯ transition duration: < 20 s (for manual transition of DUT between temperature storage and splashing);
⎯test fluid: de-ionized water;
⎯ water temperature: 0 °C to +4 °C;
⎯ water flow: between 3 l and 4 l per 3 s (splash duration);
⎯ distance between jet and DUT surface: (325 ± 25) mm (water shall be applied over the complete width of the DUT);
⎯ operating modes: see Figure 5;
⎯ orientation of the DUT: as in the vehicle.
Parameter:
| Inner size | 1000*1050*1080mm (D*W*H) Auto Parts Test Equipment |
| Temperature range | RT+10°C -160°C |
| Heating rate | RT+10°C -160°C<40min |
| Test fluid | de-ionized water |
| Volume of water tank | About 100L (Motor stirring, bottom slope, easy to clean and drain) |
| Water temperature range | 0-4°C |
| Cooling rate | The temperature should be stable at 2℃ in 30 minutes and 160℃ in the test chamber |
Company Details
Business Type:
Manufacturer
Year Established:
2012
Total Annual:
3000000-5000000
Employee Number:
50~100
Ecer Certification：
Verified Supplier
Guangzhou Hejin Automation Control Technology Co., Ltd. is a modern enterprise specialized in R & D, manufacturing and sales of technology intensive industrial equipment. Its main products include laboratory testing equipment and production line detection system, which are widely applied to refr... Guangzhou Hejin Automation Control Technology Co., Ltd. is a modern enterprise specialized in R & D, manufacturing and sales of technology intensive industrial equipment. Its main products include laboratory testing equipment and production line detection system, which are widely applied to refr...
Get in touch with us
Leave a Message, we will call you back quickly!