High Quality BLDC Hall Sensor Motor Cotroller 110/220VAC Input Continuous

Product Specification

High Quality BLDC Hall Sensor Motor Cotroller 110/220VAC Input Continuous Current 2-12A

Model No. BLSD11008ADC-2Q-HV

Ambient Temp. -10~45 ℃, -40-65℃

Power Voltage: 110VAC (45-140V) or 155VDC (60-195V)

Peak Current: 4-8A

Continuous Current: 2-4A

PWM: 15KHz

Ramp Time: 0.2-2.2S

Reference Input Range: 0-10V/0-3KHz Pulse/0-100% PWM @50Hz-1KHz

Alarm Output: OC

PG Output: 4 or 24 Pulse/r @8-Pole Motor

PI Close-Loop: Speed or Current.

SC Protection(A): 20

OT Protection: 65℃ or 85 ℃ at Case

Safe F/R: Smooth F/R Operation

Safe Start: Stop Until Speed is Zero at Starting

Model No. BLSD11016ADC-2Q-HV

Ambient Temp. -10~45 ℃, -40-65℃

Power Voltage: 110VAC (45-140V) or 155VDC (60-195V)

Peak Current: 8-16A

Continuous Current: 4-8A

PWM: 15KHz

Ramp Time: 0.2-2.2S

Reference Input Range: 0-10V/0-3KHz Pulse/0-100% PWM @50Hz-1KHz

Alarm Output: OC

PG Output: 4 or 24 Pulse/r @8-Pole Motor

PI Close-Loop: Speed or Current.

SC Protection(A): 40

OT Protection: 65℃ or 85 ℃ at Case

Safe F/R: Smooth F/R Operation

Safe Start: Stop Until Speed is Zero at Starting

Model No. BLSD11024ADC-2Q-HV

Ambient Temp. -10~45 ℃, -40-65℃

Power Voltage: 110VAC (45-140V) or 155VDC (60-195V)

Peak Current: 12-24A

Continuous Current: 6-12A

PWM: 15KHz

Ramp Time: 0.2-2.2S

Reference Input Range: 0-10V/0-3KHz Pulse/0-100% PWM @50Hz-1KHz

Alarm Output: OC

PG Output: 4 or 24 Pulse/r @8-Pole Motor

PI Close-Loop: Speed or Current.

SC Protection(A): 60

OT Protection: 65℃ or 85 ℃ at Case

Safe F/R: Smooth F/R Operation

Safe Start: Stop Until Speed is Zero at Starting

Model No. BLSD22008ADC-2Q-HV

Ambient Temp. -10~45 ℃, -40-65℃

Power Voltage: 220VAC (45-275V) or 310VDC (60-385V)

Peak Current: 4-8A

Continuous Current: 2-4A

PWM: 15KHz

Ramp Time: 0.2-2.2S

Reference Input Range: 0-10V/0-3KHz Pulse/0-100% PWM @50Hz-1KHz

Alarm Output: OC

PG Output: 4 or 24 Pulse/r @8-Pole Motor

PI Close-Loop: Speed or Current.

SC Protection(A): 20

OT Protection: 65℃ or 85 ℃ at Case

Safe F/R: Smooth F/R Operation

Safe Start: Stop Until Speed is Zero at Starting

Model No. BLSD22016ADC-2Q-HV

Ambient Temp. -10~45 ℃, -40-65℃

Power Voltage: 220VAC (45-275V) or 310VDC (60-385V)

Peak Current: 8-16A

Continuous Current: 4-8A

PWM: 15KHz

Ramp Time: 0.2-2.2S

Reference Input Range: 0-10V/0-3KHz Pulse/0-100% PWM @50Hz-1KHz

Alarm Output: OC

PG Output: 4 or 24 Pulse/r @8-Pole Motor

PI Close-Loop: Speed or Current.

SC Protection(A): 40

OT Protection: 65℃ or 85 ℃ at Case

Safe F/R: Smooth F/R Operation

Safe Start: Stop Until Speed is Zero at Starting

Model No. BLSD22024ADC-2Q-HV

Ambient Temp. -10~45 ℃, -40-65℃

Power Voltage: 220VAC (45-275V) or 310VDC (60-385V)

Peak Current: 12-24A

Continuous Current: 6-12A

PWM: 15KHz

Ramp Time: 0.2-2.2S

Reference Input Range: 0-10V/0-3KHz Pulse/0-100% PWM @50Hz-1KHz

Alarm Output: OC

PG Output: 4 or 24 Pulse/r @8-Pole Motor

PI Close-Loop: Speed or Current.

SC Protection(A): 60

OT Protection: 65℃ or 85 ℃ at Case

Safe F/R: Smooth F/R Operation

Safe Start: Stop Until Speed is Zero at Starting

Selection Table

Notice

1. Select peak current of driver: IP≥2*Irm or IP≥4*Pom/(1.414*Vp), Irm=rated current of moto (A), Pom=Rated Output power of motor (W), Vp=AC Supply voltage of driver (Vrms)
2. Driving quadrant: The drivers are only used in I & III quadrant.
3. Interference from leads: The Hall signals can be disturbed by switched current in windings leads when length is more than 3m. Don’t interwire them together. It is better to use shield leads
4. Motor Insulation: Hall sensors to windings/Hall sensors to Motor Case/Windings to Motor Case

Insulation Resistance＞100MOhm @ 1500VDC

Dielectric strength ＜1 mA@1200VAC/50-60Hz/1 minute

5. Safety: The PE terminal labeled on the driver must be connected to the protection earth point of the supply system.