High selling Rear Brake Wear Sensor 4M0615121D for FAW Audi RSQ8

100% OEM Precise Matching, Plug-and-Play Installation Without Modification

Full Compatible Vehicle List

1. FAW & Imported Audi RSQ8 4MN chassis (2019-2025)
2. Shared platform performance Audi models: RS6 C8 Avant, RS7 C8 Sportback, S8, A8 D5, SQ7/SQ8
3. Shared platform luxury models: Lamborghini Urus, Bentley Bentayga

Matching Powertrain

Installation Position

Optimized Heavy-Duty Structural Design

1. High-temperature resistant reinforced silicone wire sheath: Tolerates continuous baking heat up to 320°C, anti-aging, oil and coolant corrosion resistant, avoids wire cracking and circuit short-circuit
2. Dual thin copper alloy sensing tips: Stable resistance signal transmission, accurately triggers dashboard warning when friction material wears down to the 3mm safety threshold
3. Fully sealed 2-pin waterproof locking plug with built-in rubber sealing ring: Blocks rainwater, mud and dust intrusion, prevents poor electrical contact and false fault alarms
4. Multi-point integrated fixed plastic positioning buckles: Firmly fix the sensor wire along the caliper bracket, eliminate wire shaking and friction damage against brake discs or calipers
5. Complete one-piece finished Y-type sensor assembly, ready for synchronous replacement with rear brake pads

Core Vehicle Safety Protection Functions

1. Transmit real-time brake pad thickness signals to the vehicle ECU, activate dashboard wear warning light to prompt timely pad replacement, prevent irreversible metal grinding damage to costly rear brake rotors
2. Stable electrical signal output under extreme high-temperature heavy braking of performance SUVs, no monitoring failure during long downhill driving
3. Waterproof and shockproof all-weather design adapts to city, mountain and off-road road conditions, avoids sudden brake monitoring system breakdown during high-speed driving
4. Standard OEM plug interface ensures stable circuit communication, eliminates redundant diagnostic fault codes after brake maintenance work

Common Solvable Vehicle Faults

• Brake pad wear warning light stays illuminated after installing new rear brake pads
• Intermittent brake fault pop-up when driving over bumpy uneven roads
• Diagnostic scanner reads brake wear sensor open-circuit or short-circuit fault codes
• No warning reminder when rear brake pads are severely worn thin
• Water and mud infiltration causes unstable electrical connection and random abnormal alarms

Step-by-Step Installation Instructions

Required Tools

Operation Steps

1. Park vehicle on flat ground, engage electronic parking brake, loosen rear wheel lug nuts slightly before jacking up the rear axle, secure the vehicle firmly with jack stands.
2. Remove rear wheel, locate the electrical plug of the old wear sensor behind the brake caliper, press the lock buckle and unplug the connector.
3. Hang the rear brake caliper with a bungee cord (do not suspend the caliper by the brake hose to avoid oil pipe damage), remove old rear brake pads.
4. Use a flat screwdriver to gently pry out the old sensor from the pad clamping groove; do not pull hard on the wire to avoid breaking the internal sensing copper wire.
5. Clean the pad mounting groove and caliper bracket with brake cleaner to remove rust, dust and residual brake powder.
6. Insert the dual sensing tips of the new 4M0615121D sensor into the reserved slots of the new inner rear brake pad, push until you hear an audible locking click to ensure the sensor fits flush against the pad back plate.
7. Install the new pad-sensor assembly back onto the caliper bracket, arrange the sensor wire neatly along the caliper guide, use built-in positioning buckles to fix the wire and avoid contact with rotating brake discs.
8. Reinstall the brake caliper, tighten caliper bolts to factory specified torque, plug the sensor electrical connector firmly until the lock buckle clicks.
9. Remount rear wheel, lower the vehicle to the ground and torque wheel lug nuts to standard value.
10. Start the engine, step on the brake pedal slowly 8-10 times to seat new brake pads. Take a low-speed test drive; use a VCDS/OBD diagnostic scanner to clear stored brake fault codes if the warning light remains on.

Strict Factory Testing & Stable Spot Supply