Shenzhen ECER Network Technology Co., Ltd.
| Connector Type | RJ45插座 |
| PoE | 不带PoE |
| Number of Ports | 1 |
| Shielding | 有屏蔽 |
| Mounting Type | 弯插 |
| Supplementary Features | 鱼叉脚(塑料) |
| LED | 不带LED |
| Description | Jack Modular Connector RJ45 Through Hole, Right Angle |
| Mfr. Part # | RJ-056-1-4 |
| Package | Through Hole,Right Angle |
| Model Number | RJ-056-1-4 |
View Detail Information
Explore similar products
RJ45 Jack with Magnetic Module ABRACON ARJ11E MBSA A B EM2 Supporting 1000 Base
Network communication components featuring Bel Fuse SS-7188S-A-NF-1-50 for
ABRACON ARJ11G MBSD LU2 Vertical Mount RJ45 10 100 Base T Connector with
Connector Protective Coating Bel Fuse SS65600-004F for Long Term Durability and
Product Specification
| Connector Type | RJ45插座 | PoE | 不带PoE |
| Number of Ports | 1 | Shielding | 有屏蔽 |
| Mounting Type | 弯插 | Supplementary Features | 鱼叉脚(塑料) |
| LED | 不带LED | Description | Jack Modular Connector RJ45 Through Hole, Right Angle |
| Mfr. Part # | RJ-056-1-4 | Package | Through Hole,Right Angle |
| Model Number | RJ-056-1-4 |
RJ45 network socket connector. This product specification covers performance, tests, and quality requirements for RJ45 connectors. All inspections shall be performed using the applicable inspection plan and product drawing.
| Category | Item | Requirement | Test Procedure |
|---|---|---|---|
| Requirements | Standard atmospheric condition | Ambient temperature: 15 to 35 Relative humidity: 63% to 67% Air pressure: 86 kpa to 106 kpa | Unless otherwise specified |
| Temperature | Operating: -25 to 85 Storage: -40 to 85 | ||
| Ratings | Voltage: 125 Volts Current: 1.5 Amperes | ||
| Dimension | Refer to applicable product drawing | ||
| Performance and Test Description | Appearance | Product shall meet requirements of applicable product drawing and specification. | Visual, dimensional and functional per applicable quality inspection plan. |
| Electrical | Low Level Contact Resistance | Terminal Pin1-Pin8: 40 milliohms maximum initial, 40 milliohms maximum after test Switch: 100 milliohms maximum initial, 100 milliohms maximum after test | Mate subject connector with compatible connector. Then measure and record the contact resistance of the specimen under test with a test current of 100 mill-amperes maximum and 20 mill-volts open circuit voltage maximum. |
| Insulation Resistance | 500 Mega ohms minimum initial 200 Mega ohms minimum final | After 500 VDC for 1 minute, measure the insulation resistance between the adjacent contacts of mated and unmated connector assemblies. | |
| Dielectric Withstanding Voltage | 1 minute hold with no breakdown or flashover. Voltage: 500 VDC Current leakage: 10.0 mA max. | Test between adjacent contacts of unmated connector assemblies. | |
| Mechanical | Mating force | 25N Max. | Measure force necessary to mate the connector assemblies at a max of 12.5 mm/minute. |
| Durability | 750 cycles. Shall meet visual requirements, show no physical damage. | Mate and unmated connector assemblies for 750 cycles at a maximum rate of 20 cycles/min. | |
| Environmental | Heat test | The insulation resistance must coincide previously specification. Shall meet visual requirements, show no physical damage. | Subject mated connectors to 85 2 for 96 hours. It shall be subjected to standard atmospheric condition for 1 hour after which measurements shall be made. |
| Steady State Humidity | The insulation resistance must coincide previously specification. Shall meet visual requirements, show no physical damage. | Subject mated connectors to relative humidity of 90% to 95%RH and a temperature of 40 2 for 96 hours. It shall be subjected to standard atmospheric condition for 1 hour after which measurements shall be made. | |
| Salt Spray | Shall meet visual requirements, show no physical damage. | Subject mated connectors to 51% salt-solution concentration, 35+1/-2 for 8 hours. | |
| Mounting characteristics | Solderability | Solderable area shall have minimum of 95% solder coverage. | Dip the pin in flux of R type for 5-10 seconds. Immerse the solder pin of the connector in the solder bath at 2455 for 4.0-5.0 seconds. |
| Mounting characteristics | Resistance to soldering heat | The contact resistance must coincide previously specification. Shall meet visual requirements, show no physical damage. | Reflow Soldering Conditions: Preheat: 180, 20.3 minutes. Soldering heat: Peak temperature 2605 within 10 seconds. Soldering iron method: Bit temperature 35010, application time 1~5 sec. |
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification：
Verified Supplier
Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability... Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability...
Get in touch with us
Leave a Message, we will call you back quickly!