Shenzhen ECER Network Technology Co., Ltd.
| Mounting Type | 弯插 |
| Connector Type | DC电源插座 |
| Rated current | 2A |
| working temperature | -20℃~+70℃ |
| Inside Contact Diameter | 2mm |
| Rated voltage | 30V |
| Outside Contact Diameter | 6.4mm |
| Description | Power Barrel Connector Jack 2mm ID 6.4mm OD Through Hole, Right Angle |
| Mfr. Part # | DC+02IB |
| Package | Through Hole |
| Model Number | DC+02IB |
View Detail Information
Explore similar products
circular connector Amphenol HVSLS600062A025 with 37 contacts aluminum alloy
Industrial DC Power Socket kinghelm KH-DC-005B-2.5 Connector Suitable for
DC power connector HMTCONN DC005-B25 with 5000 cycles service life and wide
Field installable plastic power connector Amphenol UPCP012ALS2 featuring RADSOK
Product Specification
| Mounting Type | 弯插 | Connector Type | DC电源插座 |
| Rated current | 2A | working temperature | -20℃~+70℃ |
| Inside Contact Diameter | 2mm | Rated voltage | 30V |
| Outside Contact Diameter | 6.4mm | Description | Power Barrel Connector Jack 2mm ID 6.4mm OD Through Hole, Right Angle |
| Mfr. Part # | DC+02IB | Package | Through Hole |
| Model Number | DC+02IB |
This specification applies to DC POWER JACK connectors used in electronic products. These connectors are designed for reliable power input in various electronic devices.
| Item | Property | Test Condition | Performance |
|---|---|---|---|
| Rated / | Practical temperature range | -20to +70 | 85% RH.MAX. Humidity |
| Rated voltage and current(MAX.) | 30V DC , 2A | ||
| Electrical efficiency / | Withstand Voltage | Withstand AC 500V (50/60Hz RMS) between two non-contact terminals for 1 minute | No dielectric breakdown shall occur. |
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 100 M Min. | |
| Contact Resistance | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA) | 30 m MAX. | |
| Mechanical Performance | Insertion and Extraction Force | Plug and unplug with a matching plug at a frequency of 20-30 times per minute. | Insertion and extraction force is 0.33kgf |
| Terminal Strength | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | No looseness, damage, etc., but the terminal deformation is acceptable. | |
| Durability / | Life test | Under the condition of no load, plug and unplug with a matching plug for 5000 times in total, at a frequency of 20-30 times per minute. | Appearance no obvious change, destruction. Contact resistance: less than 30 m. Insertion and extraction force values: 0.3 to 3 kgf. |
| Solderability / | Resistance to soldering heat | The jack terminal should be dipped in solder: Temperature of solder: 2603. Dip time: 51 seconds. | After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base. |
| Solderability | Temperature of solder: 2453C. Time of dip: 30.5 seconds. | Coating of solder area should be more than 95% | |
| Environment test / | Cold test | Place the housing for 96 hours at a low temperature of -25 3 C. Then ,place it under standard atmospheric conditions for 1 hour and test. | No obvious change in appearance. Contact resistance: 100m max. Insulation resistance: 100 M min. Withstand voltage: AC 500V. |
| Heat test | The housing should be stored at a temperature of 852for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | ||
| Humidity test | The housing should be stored at a temperature of 403with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | No obvious change in appearance. Contact resistance: 100m max. Insulation resistance: 100 M min. Withstand voltage: AC 500V. | |
| Salt spray test | Temperature: 35 2 Solution: 5 1% Spray time: 24hours Wash and dry it at room temperature after the experiment. | No obvious rust in the appearance. |
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification：
Verified Supplier
Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability... Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability...
Get in touch with us
Leave a Message, we will call you back quickly!