Shenzhen ECER Network Technology Co., Ltd.
| Mounting Type | 弯插 |
| Connector Type | DC电源插座 |
| Rated current | 2A |
| working temperature | -20℃~+70℃ |
| Inside Contact Diameter | 2mm |
| Rated voltage | 30V |
| Outside Contact Diameter | 6.4mm |
| Description | Power Barrel Connector Jack 2mm ID 6.4mm OD Through Hole, Right Angle |
| Mfr. Part # | DC+02D-03 |
| Package | Through Hole |
| Model Number | DC+02D-03 |
View Detail Information
Explore similar products
circular connector Amphenol HVSLS600062A025 with 37 contacts aluminum alloy
Industrial DC Power Socket kinghelm KH-DC-005B-2.5 Connector Suitable for
DC power connector HMTCONN DC005-B25 with 5000 cycles service life and wide
Field installable plastic power connector Amphenol UPCP012ALS2 featuring RADSOK
Product Specification
| Mounting Type | 弯插 | Connector Type | DC电源插座 |
| Rated current | 2A | working temperature | -20℃~+70℃ |
| Inside Contact Diameter | 2mm | Rated voltage | 30V |
| Outside Contact Diameter | 6.4mm | Description | Power Barrel Connector Jack 2mm ID 6.4mm OD Through Hole, Right Angle |
| Mfr. Part # | DC+02D-03 | Package | Through Hole |
| Model Number | DC+02D-03 |
This specification applies to DC POWER JACK connectors used in electronic products. Designed for reliable electrical connections, these jacks offer specific operational and environmental tolerances.
| Item | Property | Test Condition | Performance |
| 2. Rated / | Practical temperature range | -20 to +70 | 85% RH.MAX. Humidity |
| Preservation temperature range | -10 to +40 | 85% RH.MAX. Humidity | |
| Rated voltage and current (MAX.) | 30V DC, 2A | ||
| Appearance | No scratches, soil, rust or discoloration on the surface. | ||
| 4. Electrical efficiency / | Withstand Voltage | Withstand AC 500V (50/60Hz RMS) between two non-contact terminals for 1 minute | No dielectric breakdown shall occur. |
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 100 M Min. | |
| Contact Resistance | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA) | 30 m MAX. | |
| 5. Mechanical Performance / | Insertion and Extraction Force | Plug and unplug with a matching plug at a frequency of 20-30 times per minute. | 0.33kgf |
| Terminal Strength | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | No looseness, damage, etc., but terminal deformation is acceptable. | |
| 6. Durability / | Life test | Under no load, plug and unplug with a matching plug for 5000 times at a frequency of 20-30 times per minute. | Appearance: No obvious change or destruction. Contact resistance: < 30 m. Insertion/extraction force: 0.3 to 3 kgf. |
| 7. Solderability / | Resistance to soldering heat | Terminal dipped in solder at 2603 for 51 seconds. | Plastic base should not be deformed, terminals should not fall off. |
| Solderability | Solder temperature: 2453C. Dip time: 30.5 seconds. | Coating of solder area should be more than 95%. | |
| 8. Environment test / | Cold test | Housing placed at -25 3 C for 96 hours, then under standard atmospheric conditions for 1 hour. | Appearance: No obvious change. Contact resistance: 100m max. Insulation resistance: 100 M min. Withstand voltage: AC 500V. |
| Heat test | Housing stored at 852 for 96 hours, then under standard atmospheric conditions for 1 hour. | (Performance details not explicitly stated for heat test alone, but implied to meet general standards) | |
| Humidity test | Housing stored at 403 with 90% ~ 95% RH for 96 hours, then under standard atmospheric conditions for 1 hour. | Appearance: No obvious change. Contact resistance: 100m max. Insulation resistance: 100 M min. Withstand voltage: AC 500V. | |
| Salt spray test | Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Washed and dried at room temperature after experiment. | No obvious rust in the appearance. | |
| 9. Test condition / | Standard Conditions | Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. | For doubtful judgments: 201C, 63% to 67% RH, 86 kPa to 106 kPa. |
| 10. Amendment / | Modification Process | Specifications require negotiation and agreement between manufacturer and customer. | N/A |
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification：
Verified Supplier
Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability... Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability...
Get in touch with us
Leave a Message, we will call you back quickly!