Shenzhen ECER Network Technology Co., Ltd.
| Number of Ports | 1 |
| Interface | 内针 |
| RF Series | IPEX |
| Connector Type | 板端 |
| Style | - |
| Operating Temperature | -40℃~+90℃ |
| Frequency | 6GHz |
| Impedance | 50Ω |
| Interface Diameter | 2mm |
| Description | Connector Receptacle IPEX Male Pin 500Ω Surface Mount |
| Mfr. Part # | HX IPEX 1.0-3P |
| Package | SMD |
| Model Number | HX IPEX 1.0-3P |
View Detail Information
Explore similar products
Brass gold plated communication assembly with insulator pin pins and rear plug
Professional grade kinghelm KH-MMCX-K510-Z connector cable suitable for
Crimp Non Solder TNC Male Connector L com EZ 600 TM X LC for Laboratory and
High Voltage 50 Ohm Male Clamp Coaxial Connector L-com ANM-2602 with Brass
Product Specification
| Number of Ports | 1 | Interface | 内针 |
| RF Series | IPEX | Connector Type | 板端 |
| Style | - | Operating Temperature | -40℃~+90℃ |
| Frequency | 6GHz | Impedance | 50Ω |
| Interface Diameter | 2mm | Description | Connector Receptacle IPEX Male Pin 500Ω Surface Mount |
| Mfr. Part # | HX IPEX 1.0-3P | Package | SMD |
| Model Number | HX IPEX 1.0-3P |
This document outlines the specifications for the HX IPEX 1.0-3P Antenna Seat, a product from Shenzhen Hanxia Electronic Co., Ltd. It details the product's requirements, testing procedures, and performance criteria to ensure functionality and reliability in various operating conditions.
| Item | Requirements | Test Method |
|---|---|---|
| 1.1 Application Condition | ||
| Operating Environment | Temperature: -40C to +90C, Relative Humidity: 25%~85%, Without loss of function. | |
| Storage Environment | Temperature: -55C to +100C, Relative Humidity: 95% or Less, Without loss of function. | |
| Ratings | Voltage Rating: 60VAC Nominal characteristic impedance: 50 Frequency: DC0.1~6GHz | |
| VSWR | Plug: 1.3 Max. (DC0.1~3GHz), 1.5 Max. (3~6GHz) Receptacle: 1.3 Max. (DC0.1~3GHz), 1.4 Max. (3~6GHz) | |
| 1.4 Test Requirements and Methods | ||
| Product Appearance | All components shall be properly assembled and free of burrs, warps, scratches, broken chips, and other abnormalities. Comply with method EIA 364-18B. | Visual, functional, and dimensional inspection complies with applicable specification and document. |
| Low Level Contact Resistance | Initial: 20m Max. Final: 70m Max. | |
| Insulation Resistance | Initial: 500 M Min. Final: 100 M Min. Comply with method EIA-364-21D. Insulation resistance is measured between adjacent contacts after applying 100V DC for 1 minute. | |
| Dielectric Withstanding Voltage | Current leakage: 0.50 mA Max. No evidence of breakdown or flash burn. No burn caused by short circuit. No insulation destruction. Comply with method EIA-364-20D, Test Method B. Apply 300V AC for 1 minute at sea level on tested plug and connectors. | |
| VSWR | Frequency: 100M~6GHz. Measure the VSWR as shown by the network analyzer. | |
| Un-mating force | Total un-mate force: Initial 5N Min. after 30 cycles 3N Min. Un-mate the receptacle connector (soldered to the test board) and plug at a speed 253mm/minutes along the mating by the push-on/pull-off machine. | |
| Crimp strength | 5N MIN. Pull the cable as shown at a speed 253mm/minutes by tensile strength machine. | |
| Durability | Contact resistance of inner contact: initial 20m MAX, after testing 40m MAX. Contact resistance of ground contact: initial 20m MAX, after testing 40m MAX. Appearance: No abnormality. Mate and un-mate the receptacle connector (soldered to the test board) and plug 30 cycles at a speed 253mm/minutes along the mating by the push-on/pull-off machine. Comply with method EIA 364-09C. | |
| Cable retention force | Appearance: Looseness between the parts, chipping, breakage or other abnormality shall not occur. Electrical discontinuity: No electrical discontinuity greater than 1 micro-sec. shall occur. Contact resistance of inner contact: initial 20m MAX, after testing 40m MAX. Contact resistance of ground contact: initial 20m MAX, after testing 40m MAX. Apply force on the cable as shown. During the testing, run 100mA DC to check electrical discontinuity. | |
| Vibration | Appearance: No abnormality. Electrical discontinuity: No electrical discontinuity greater than 1 micro-sec. shall occur. Contact resistance of inner contact: initial 20m MAX, after testing 40m MAX. Contact resistance of ground contact: initial 20m MAX, after testing 40m MAX. Apply the following vibration to the mating connector. Frequency: 10Hz-100Hz-10Hz/approx 20 minutes. Half amplitude, peak value of acceleration: 1.5mm or 59m/s(6G). Directions, cycle: 3 mutually perpendicular directions, 3 cycles for each direction. During the testing, run 100mA DC. Comply with method EIA 364-28E. | |
| Physical shock | Appearance: Looseness between the parts, chipping, breakage or other abnormality shall not occur. Electrical discontinuity: No electrical discontinuity greater than 1 micro-sec. shall occur. Contact resistance of inner contact: initial 20m MAX, after testing 40m MAX. Contact resistance of ground contact: initial 20m MAX, after testing 40m MAX. Apply the following vibration to the mating connector in accordance with MIL-STD-202, Method 213, Condition B. During the testing, run 100mA DC to check electrical discontinuity. Peak value of acceleration: 735m/s(75G). Duration: 11msec. Wave Form: half sinusoidal. Directions, cycle: 6 mutually perpendicular, 3 cycles about each direction. Comply with method EIA 364-27B. | |
| Humidity | Appearance: Looseness between the parts, chipping, breakage or other abnormality shall not occur. Contact resistance of inner contact: initial 20m MAX, after testing 40m MAX. Contact resistance of ground contact: initial 20m MAX, after testing 40m MAX. Insulation resistance: initial 500 mega-ohm MIN, after testing 100 mega-ohm MIN. D.W.Voltage: No creeping discharge, flashover, nor insulator breakdown shall occur. Apply the following environment to the mating connector in accordance with Temperature: 3132K(402C), Humidity: 90~95%RH, Duration: 96 hours. Comply with method EIA 364-31C, Method II, Condition A. | |
| Thermal shock | Appearance: Looseness between the parts, chipping, breakage or other abnormality shall not occur. Contact resistance of inner contact: initial 20m MAX, after testing 40m MAX. Contact resistance of ground contact: initial 20m MAX, after testing 40m MAX. Insulation resistance: initial 500 mega-ohm MIN, after testing 100 mega-ohm MIN. D.W.Voltage: No creeping discharge, flashover, nor insulator breakdown shall occur. Apply the following environment to the mating connector. Temperature: 218K(-55C) : 30 min. 358K(85C): min. Transition time: 5 min. Max. No.of cycles: 5 cycles. Comply with method EIA 364-32E. | |
| Temperature Life | Appearance: Looseness between the parts, chipping, breakage or other abnormality shall not occur. Contact resistance of inner contact: initial 20m MAX, after testing 40m MAX. Contact resistance of ground contact: initial 20m MAX, after testing 40m MAX. Apply the following environment to the mating connector in accordance with Temperature: 3632K(902C), Duration: 96 hours. Comply with method EIA 364-17B. | |
| H2S Gas | Appearance: No abnormality adversely affecting the performance shall occur. Contact resistance of inner contact: initial 20m MAX, after testing 40m MAX. Contact resistance of ground contact: initial 20m MAX, after testing 40m MAX. Apply the following environment to the mating connector in accordance with Temperature: 3132K(402C), Humidity: 805%RH, Gas: H2S 31ppm, Duration: 96 hours. | |
| Salt Mist Test | Appearance: No abnormality adversely affecting the performance shall occur. Contact resistance of inner contact: initial 20m MAX, after testing 40m MAX. Contact resistance of ground contact: initial 20m MAX, after testing 40m MAX. Apply the following environment to the mating connector in accordance with MIL-STD-202, Method 101, Condition B. Temperature: 3082K(352C), Salt water density by weight: 51%, Duration: 48 hours. Comply with method EIA 364-26B, Method 101, Condition B. | |
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification：
Verified Supplier
Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability... Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability...
Get in touch with us
Leave a Message, we will call you back quickly!