Shenzhen ECER Network Technology Co., Ltd.
| Flame Retardant Rating | - |
| Pitch | 2mm |
| colour | 白色 |
| Number of Rows | 2 |
| With Wings | 不带翅 |
| Reference Series | JWPF |
| Operating Temperature | -25℃~+85℃ |
| Plastic Material | PBT |
| Number of PINs Per Row | 5 |
| Number of Positions or Pins | 2x5P |
| With Locker | 带锁扣 |
| Row Spacing | 4mm |
| Description | Connector Housing 10 Position 2mm Pitch Dual Row JWPF Series PBT -25℃~+85℃ |
| Mfr. Part # | HC-JWPF-2x5Y-05 |
| Package | P=2mm |
| Model Number | HC-JWPF-2x5Y-05 |
View Detail Information
Explore similar products
Dependable kinghelm KH-A2009-2X12Y component built for consistent performance in
Connector solution featuring HRS DF1B-22DEP-2.5RC 2.5mm pitch for discrete wire
HRS DF51K-2S-2C 800 connector optimized for automotive applications requiring
Wire to board crimp connector JST PAP 05V S with 2 millimeter pitch and
Product Specification
| Flame Retardant Rating | - | Pitch | 2mm |
| colour | 白色 | Number of Rows | 2 |
| With Wings | 不带翅 | Reference Series | JWPF |
| Operating Temperature | -25℃~+85℃ | Plastic Material | PBT |
| Number of PINs Per Row | 5 | Number of Positions or Pins | 2x5P |
| With Locker | 带锁扣 | Row Spacing | 4mm |
| Description | Connector Housing 10 Position 2mm Pitch Dual Row JWPF Series PBT -25℃~+85℃ | Mfr. Part # | HC-JWPF-2x5Y-05 |
| Package | P=2mm | Model Number | HC-JWPF-2x5Y-05 |
This specification applies to the 2.00 series connector strip, covering product performance, test methods, and inspection requirements. It is designed for use with AWG #22~#26 wires and PC board thicknesses of 0.8~1.6mm, operating within an ambient temperature range of -25 to +85.
| Item | Requirement | Test Mode |
| Electrical Performance | Withstand voltage: 1000V AC (rms) for 1 minute, leakage current < 0.5mA | Apply 1000V AC(rms)for I minute and the leakage current shall not exceed 0.5mA to the adjacent termina1 and ground of the mate connectors |
| Contact Resistance: 20m (Initial value) | A maximum voltage of 20m V and maximum current of 1OOmA are applied to the Mate connector | |
| Insulation Resistance: 1000 M | Apply 500V DC(rms) for I minute between adjacent contacts to measure the insulation resistance | |
| Rated Voltage: 100V AC/DC, Rated Current: 3A AC/DC | - | |
| Mechanical Performance | Single contact insertion force: 5N | Housing together with the terminal ends with wafer matched at a rate per minute to 253mm inserting force test |
| Single contact Withdrawal force: 0.5N | Terminal and hole seat matched at a rate per minute to 253mm along the wire direction, pulled out from the hole seat | |
| Terminal crimping Wire strength: AWG#22: 15N, AWG#24: 30N, AWG#26: 20N | Axial pullout force at rate of 253mm per minute on crimped wire | |
| Pin Retention Force: 15N | Force applied on pin end at rate of 253mm per minute until needle exits seat | |
| Vibration: Amplitude 1.5mm p-p, Frequency 10-55-10 Hz/min, Duration 2 hours per direction (X, Y, Z axes), Current Discontinuity: 1 sec Max, Contact Resistance: 40m | Mate connector combination state, tested as per specification, check for discontinuous current, measure contact resistance after test | |
| Durability: 30 cycles (10 cycles/min) | Mate connectors up 30 cycles at a Maximum rate of 10 cycles per minute prior to environmental test, Contact Resistance: 40m | |
| Environmental Performance | Thermal Aging: Temperature 852, Period 96 hours continuously | Connector combination condition placed in high temperature aging test, measure contact resistance after test, Appearance: No damage, Contact Resistance: 40m |
| Temperature Rise: Measure temperature rise of contact when maximum rated current is passed | Mate connector measure the temperature rise of contact when the maximum rated current is passed | |
| Constant Humidity: Temperature 402, Relative humidity 90-95% RH, Period 96 hours continuously | Connector combination condition placed in constant temperature and humidity, measure contact resistance, insulation resistance, and withstand voltage after test, Appearance: No damage, Contact Resistance: 40m , Insulation Resistance: 1000m | |
| Salt Spray: Temperature 353, Concentration 51%, Period: 8 hours (after plating) / 48 hours (before plating) | Connector combination condition subjected to salt spray test, cleaned with water and dried naturally, measure contact resistance, Appearance: No damage, Contact Resistance: 40m |
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification：
Verified Supplier
Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability... Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability...
Get in touch with us
Leave a Message, we will call you back quickly!