Shenzhen ECER Network Technology Co., Ltd.
| Flame Retardant Rating | - |
| Pitch | 2mm |
| colour | 蓝色 |
| Number of Rows | 1 |
| With Wings | 不带翅 |
| Reference Series | PH |
| Operating Temperature | -25℃~+85℃ |
| Plastic Material | PA66 |
| Number of PINs Per Row | 2 |
| Number of Positions or Pins | 1x2P |
| With Locker | 不带锁扣 |
| Row Spacing | - |
| Description | Connector Housing 2 Position 2mm Pitch Single Row PH Series PA66 -25℃~+85℃ |
| Mfr. Part # | HC-PH-2Y-L-05 |
| Package | P=2mm |
| Model Number | HC-PH-2Y-L-05 |
View Detail Information
Explore similar products
Dependable kinghelm KH-A2009-2X12Y component built for consistent performance in
Connector solution featuring HRS DF1B-22DEP-2.5RC 2.5mm pitch for discrete wire
HRS DF51K-2S-2C 800 connector optimized for automotive applications requiring
Wire to board crimp connector JST PAP 05V S with 2 millimeter pitch and
Product Specification
| Flame Retardant Rating | - | Pitch | 2mm |
| colour | 蓝色 | Number of Rows | 1 |
| With Wings | 不带翅 | Reference Series | PH |
| Operating Temperature | -25℃~+85℃ | Plastic Material | PA66 |
| Number of PINs Per Row | 2 | Number of Positions or Pins | 1x2P |
| With Locker | 不带锁扣 | Row Spacing | - |
| Description | Connector Housing 2 Position 2mm Pitch Single Row PH Series PA66 -25℃~+85℃ | Mfr. Part # | HC-PH-2Y-L-05 |
| Package | P=2mm | Model Number | HC-PH-2Y-L-05 |
This specification covers the 2.00mm pitch PH connector, double row type. It details product performance, test methods, and inspection requirements for electrical and mechanical applications.
| Item | Requirement | Test Mode |
| General Principles | ||
| Scope | This specification applies to the 2.0 series connector strip, including product performance, test methods and test requirements. | |
| Applicable Standards | GB/T2421, GB/T2423, GB/T2424, GB/T5095 | |
| Appearance | Product surface without defect, dirt, crack, and mechanical damage; contact parts without rust, plating oxidation, peeling, etc. | |
| Exchangeability | Products of the same specification should be interchangeable. | |
| Use Condition | ||
| Ambient Temperature | -25 +85 | |
| Applicable Wire Sizes | AWG #24#30 | |
| Applicable PC Board Thickness | 0.81.6mm | |
| Electrical Performance | ||
| Rated Voltage | 100V AC/DC | |
| Rated Current | 2A AC/DC | |
| Withstand Voltage | No breakdown or flashover | Apply 800V AC(rms) for 1 minute and the leakage current shall not exceed 0.5mA to the adjacent terminal and ground of the mate connectors |
| Contact Resistance | 20m (Initial value) | Apply a maximum voltage of 20mV and maximum current of 100mA to the mate connector. Does not include wire resistance. |
| Insulation Resistance | 1000 M | Apply 1000V DC (rms) for 1 minute between adjacent contacts to measure the insulation resistance. |
| Mechanical Performance | ||
| Terminal Crimping Wire Strength | 30N (AWG#24), 20N (AWG#26), 13N (AWG#28), 8N (AWG#30) | Axial pullout force at a rate of 25 3mm per minute. |
| Fixed Terminals and Hole Seat | 12N | The terminal and the hole seat are pulled out from the hole in the seat capacity at a rate of 25 3mm per minute along the wire direction. |
| Single Contact Withdrawal Force | 2N | Single contact withdrawal force. |
| Fixed Pin Force | 12N | Force is applied to the pin end at a rate of 25 3mm per minute until the needle exits the seat. |
| Single Contact Insertion Force | 10N | Housing together with terminal ends with wafer matched at a rate of 25 3mm per minute inserting force test. |
| Durability | Contact Resistance 40m; Appearance: No damage | Mate connectors up to 30 cycles at a maximum rate of 10 cycles per minute prior to environmental test. |
| Vibration | Contact Resistance 40m; Current Discontinuity: Max 1 micro second | Mate connector combination state on the welding circuit board as test samples, subjected to vibration test. Amplitude: 1.5mm p-p; Frequency: 10-55-10Hz/minute; Duration: 2 hours for each direction (X, Y, Z axes). |
| Environmental Performance | ||
| Thermal Aging | Contact Resistance 40m; Appearance: No damage | Connector combination placed in a heating oven at 852 for 96 hours continuously. |
| Temperature Rise | Measure contact temperature rise when maximum rated current is passed. | |
| Constant Humidity | Contact Resistance 40m; Insulation Resistance 1000m; Appearance: No damage | Connector combination placed in a constant temperature and humidity chamber at 402 and 90-95% RH for 96 hours continuously. |
| Temperature Cycling | Appearance: No damage; Withstand Voltage: No breakdown or flashover | One cycle: -553 for 30min, then room temp for 10-15min; followed by 853 for 30min, then room temp for 10-15min. Total 5 cycles. |
| Salt Spray | Contact Resistance 40m; Appearance: No damage | Test samples placed in a salt spray chamber at 353 with 51% salt solution. Stamping after tin plated for 8 hours or Stamping before tin plated for 24 hours. |
| Solder Ability | Soldering Area: 90% | Soldering temperature: 2455; Immersion period: 3 0.5S. |
| Resistance to Soldering Heat | Appearance: No damage | Wave soldering: 2605 for 50.5S. Hand soldering: 3505 for 30.5S. Solder position: 1.5mm for DIP type, 0.5mm for SMT type from conductor/fixed piece end. |
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification：
Verified Supplier
Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability... Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability...
Get in touch with us
Leave a Message, we will call you back quickly!