| Flame Retardant Rating | - |
| Pitch | 2.5mm |
| colour | 白色 |
| Number of Rows | 1 |
| With Wings | 不带翅 |
| Reference Series | XHB |
| Operating Temperature | -25℃~+85℃ |
| Plastic Material | PA66 |
| Number of PINs Per Row | 3 |
| Number of Positions or Pins | 1x3P |
| With Locker | 带锁扣 |
| Row Spacing | - |
| Description | Connector Housing 3 Position 2.5mm Pitch Single Row XHB Series PA66 -25℃~+85℃ |
| Mfr. Part # | HC-XHB-3Y-05 |
| Package | P=2.5mm |
| Model Number | HC-XHB-3Y-05 |
View Detail Information
Explore similar products
Dependable kinghelm KH-A2009-2X12Y component built for consistent performance in
Connector solution featuring HRS DF1B-22DEP-2.5RC 2.5mm pitch for discrete wire
HRS DF51K-2S-2C 800 connector optimized for automotive applications requiring
Wire to board crimp connector JST PAP 05V S with 2 millimeter pitch and
Product Specification
| Flame Retardant Rating | - | Pitch | 2.5mm |
| colour | 白色 | Number of Rows | 1 |
| With Wings | 不带翅 | Reference Series | XHB |
| Operating Temperature | -25℃~+85℃ | Plastic Material | PA66 |
| Number of PINs Per Row | 3 | Number of Positions or Pins | 1x3P |
| With Locker | 带锁扣 | Row Spacing | - |
| Description | Connector Housing 3 Position 2.5mm Pitch Single Row XHB Series PA66 -25℃~+85℃ | Mfr. Part # | HC-XHB-3Y-05 |
| Package | P=2.5mm | Model Number | HC-XHB-3Y-05 |
This specification covers the 2.50MM PITCH XHB CONNECTOR DOUBLE ROW TYPE, designed for electrical connections. It details product performance, test methods, and inspection requirements, ensuring interchangeability with same specification products.
| Item | Requirement | Test Mode | |||||
| 1. Scope | |||||||
| General Principles | This specification content is applicable to the 2.50 series connector strip, including product performance, test methods and test requirements. | ||||||
| 2. Applicable Standards | |||||||
| GB/T2421 | Electrical electronic product environmental test - Part 1: General principles | ||||||
| GB/T2423 | Electrical electronic product environmental test methods | ||||||
| GB/T2424 | Electrical electronic product environmental test guidance | ||||||
| GB/T5095 | Basic test rules and measurement methods for electromechanical components of electrical equipment | ||||||
| 3. Use Condition | |||||||
| Ambient Temperature | -40 +105 | ||||||
| Applicable Wire Sizes | AWG #2228 | ||||||
| Applicable PC board thickness | 1.6mm | ||||||
| 4. Appearance and Dimension | |||||||
| Appearance | Product surface without defect, dirt, crack, and mechanical damage; contact parts without rust, plating oxidation, peeling, etc. | ||||||
| Dimension | According to drawings | ||||||
| Interchangeability | Exchangeable with same specification products. | ||||||
| 5. Material | |||||||
| Part No. | Type | Explain | Material | Thickness | Plating | UL Rating | Color |
| Terminal Contact | Brass | 0.64mm | Tin plating: 2.55 m | White | |||
| Housing Plastic | LCP | UL94V-0 | White | ||||
| Housing Plastic | Nylon66 | UL94V-0 | White | ||||
| Contact Plug Pin | Brass | 0.64mm | Tin plating: 2.55 m | Nature | |||
| Contact Plug Pin | Brass | 0.64mm | Tin plating: 2.55 m | White | |||
| Contact Plug Pin | Brass | 0.64mm | Tin plating: 2.55 m | White | |||
| Contact Plug Pin | Phosphor bronze | 0.2mm | Tin plating: 24 m | White | |||
| Housing Plastic Wafer | Nylon66 | UL94V-O | White | ||||
| 6. Electrical Performance | |||||||
| Rated Voltage | 250V AC/DC | ||||||
| Rated Current | 3A AC/DC | ||||||
| Withstand Voltage | Apply 1000V AC(rms) for 1 minute and the leakage current shall not exceed 0.5mA to the adjacent terminals and ground of the mate connectors. No breakdown or flashover. | ||||||
| Contact Resistance | Initial value 20m. Does not include wire resistance. A maximum voltage of 20mV and maximum current of 100mA are applied to the mate connector. | ||||||
| Insulation Resistance | More than 1000 M. Apply 500V DC(rms) for 1 minute between adjacent contacts to measure the insulation resistance. | ||||||
| 7. Mechanical Performance | |||||||
| Terminal crimping wire strength | AWG#22: 50N; AWG#24: 30N; AWG#26: 20N; AWG#28: 13N | Axial pullout force per contact at a rate of 25 3mm per minute. | |||||
| Fixed terminals and hole seat | 10N | ||||||
| Single contact insertion force | 5.5N | Housing together with terminal ends with wafer matched at a rate of 25 3mm per minute. | |||||
| Single contact Withdrawal force | 1.5N | The terminal and the hole seat at a react per minute to 25 3mm along the write direction are pulled out from the hole in the seat capacity. | |||||
| Seat pull-out force | 20N | Exerts a force on the pin end at a rate per minute 253mm until the needle exit seat. | |||||
| Pin Retention Force | |||||||
| Durability | Contact Resistance 40m; Appearance: No damage; Max Current Discontinuity 1 sec. | Mate connectors up to 30 cycles at a maximum rate of 10 cycles per minute prior to environmental test. | |||||
| Vibration | Appearance: No damage; Contact Resistance 40m. | Amplitude: 1.5mm p-p; Frequency: 10-55-10 Hz/minute; Period: 2 hours for each direction (X, Y, Z axis). | |||||
| 8. Environmental Performance | |||||||
| Thermal Aging | Appearance: No damage; Contact Resistance 40m. | Temperature: 852; Period: 96 hours continuously. | |||||
| Temperature Rise | Measure the temperature rise of contact when the maximum rated current is passed. | ||||||
| Humidity | Appearance: No damage; Contact Resistance 40m; Insulation Resistance 1000m. | Relative humidity: 90-95% (RH); Period: 96 hours continuously. Temperature: 30 Max. | |||||
| Temperature Cycling | Appearance: No damage; Contact Resistance 40m; Insulation Resistance 1000m; Withstand Voltage: No breakdown or flashover. | One cycle: -553C for 30min, room temp 10-15min. Total cycle: 5 cycles. 853C for 30min, room temp 10-15min. | |||||
| Salt Spray | Appearance: No damage; Contact Resistance 40m. | Temperature: 353; Concentration: 51%; Period: 24H. | |||||
| Solder Ability | Soldering area: 90%. | Solder temperature: 2455C; Immersion period: 3 0.5S. | |||||
| Resistance to Soldering Heat | Soldering time: 50.5S; Soldering pot: 260 5C. Position: DIP type 1.5mm from conductor/fixed piece end; SMT type 0.05mm from conductor/fixed piece end. | ||||||
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification:
Verified Supplier
Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability... Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability...
Get in touch with us
Leave a Message, we will call you back quickly!