Shenzhen ECER Network Technology Co., Ltd.
| Description | Through Hole Circular Connector Assemblies RoHS |
| Mfr. Part # | XLR-20AW-1 |
| Package | Through Hole |
| Model Number | XLR-20AW-1 |
View Detail Information
Explore similar products
Durable RoHS Compliant Connector CAX XLR-19ZP-7P Suitable for Electronic
Amphenol PT06E-12-4P SR Connector Designed for Communications Geophysical and
Panel Mount Socket Connector CAZN M12-P8A-GPFM12 European Standard M12 Series
Rear Mount Socket Plastic Waterproof Connector Pin Type PCB Board Mount CAZN E7T
Product Specification
| Description | Through Hole Circular Connector Assemblies RoHS | Mfr. Part # | XLR-20AW-1 |
| Package | Through Hole | Model Number | XLR-20AW-1 |
This specification applies to XLR jack (SPEAKON) connectors used in electronic products. These connectors are designed for audio signal applications and are not to be used as AC mains or power supply connectors.
| Item | Property | Test Condition | Performance |
| 2. Rated / | Practical temperature range | -30to +80 | |
| Humidity range | 85% RH.MAX. | ||
| Preservation temperature range | -10to +40 | ||
| Humidity range (Preservation) | 85% RH.MAX. | ||
| Storage Conditions | Ambient air free of acid, alkaline or other corrosive gases. Storage period not exceeding 180 days. | ||
| Rated voltage and current (MAX.) | 250V AC , 15A (continuous) | ||
| Audio signal rating | 30 A, duty cycle 50% | ||
| 2-4. Appearance | No scratches, soil, rust or discoloration on the surface. | ||
| 3-1. Outline And Dimension | Attachment drawing | Should match the attachment drawing. | |
| 3-2. Part And Material | Material list specifications | Should be consistent with the material list specifications. | |
| 4. Electrical efficiency | Withstand Voltage | AC 4000V (50/60Hz RMS) between two non-contact terminals for 1 minute | No dielectric breakdown shall occur. |
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, for 1 minute 5 seconds | 1000 M Min. | |
| Contact Resistance | Measure at the tail end of each terminal (voltage max 20mV, current max 100mA) for a matched pair of terminals. | 30 m MAX. | |
| 5. Mechanical Performance | Terminal Strength | Each terminal should withstand a force of 0.5 kgf for 10 seconds. | No looseness, damage, etc. Terminal deformation is acceptable. |
| 6. Durability | Life test | Under no load, plug in/out with a matching plug 5000 times at a frequency of 5 times per minute. | Appearance: No obvious change. Destruction: Contact resistance less than 50 m. |
| 7. Solderability | Resistance to soldering heat | Terminal dipped in solder at 2603 for 51 seconds. | Plastic base should not be deformed and terminals should not fall off. |
| Solderability | Solder temperature: 2453C. Dip time: 30.5 seconds. | Coating of solder area should be more than 95%. | |
| 8. Environment test | Cold test | Housing stored at -30 3 C for 96 hours, then under standard atmospheric conditions for 1 hour. | Appearance: No obvious change. Contact resistance: 50 m. Insulation resistance: 500 M. Withstand voltage: AC 1000V. |
| Heat test | Housing stored at 802 for 96 hours, then under standard atmospheric conditions for 1 hour. | ||
| Humidity test | Housing stored at 403 with 90% ~ 95% RH for 96 hours, then under standard atmospheric conditions for 1 hour. | Appearance: No obvious change. Contact resistance: 50 m. Insulation resistance: 500 M. Withstand voltage: AC 1000V. | |
| Temperature Cycling | Conditions as shown below, then placed in room temperature for 30 minutes. | ||
| Salt spray test | Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Washed and dried at room temperature after the experiment. | Appearance: No obvious rust. | |
| 9. Test condition | Standard conditions | Temperature: 15C~35C, Relative humidity: 25%~85%, Atmospheric pressure: 86 kPa~106 kPa. | |
| Doubtful judgment conditions | Temperature: 201C, Relative humidity: 63%~67%, Atmospheric pressure: 86 kPa~106 kPa. | ||
| 10. Amendment | Procedure | Amendments require negotiation and agreement between the manufacturer and the customer. |
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification：
Verified Supplier
Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability... Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability...
Get in touch with us
Leave a Message, we will call you back quickly!