Hefei Purple Horn E-Commerce Co., Ltd.
| Description | Through Hole Circular Connector Assemblies RoHS |
| Mfr. Part # | XLR-25-1-N3GR |
| Package | Through Hole |
| Model Number | XLR-25-1-N3GR |
View Detail Information
Explore similar products
Durable RoHS Compliant Connector CAX XLR-19ZP-7P Suitable for Electronic
Amphenol PT06E-12-4P SR Connector Designed for Communications Geophysical and
Panel Mount Socket Connector CAZN M12-P8A-GPFM12 European Standard M12 Series
Rear Mount Socket Plastic Waterproof Connector Pin Type PCB Board Mount CAZN E7T
Product Specification
| Description | Through Hole Circular Connector Assemblies RoHS | Mfr. Part # | XLR-25-1-N3GR |
| Package | Through Hole | Model Number | XLR-25-1-N3GR |
This specification applies to XLR jacks used in electronic products. The product is designed for professional audio and electronic applications, offering reliable connectivity.
| Item | Property | Test Condition | Performance |
| 2. Rated / | |||
| Practical temperature range | -30 to +80 | ||
| Humidity range | 85% RH.MAX. | ||
| Preservation temperature range | -10 to +40 | ||
| Preservation humidity range | 85% RH.MAX. | ||
| Storage Environment | Surrounding air free of acid, alkaline, or other corrosive gases. Storage period not exceeding 180 days. | ||
| Rated voltage and current (MAX.) | 50V AC , 6A | ||
| Appearance | No scratches, soil, rust, or discoloration on the surface. | ||
| 3. Construction / | |||
| Outline And Dimension | Should match the attachment drawing. | ||
| Part And Material | Should be consistent with the material list specifications. | ||
| 4. Electrical efficiency / | |||
| Withstand Voltage | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur. | Between two non-contact terminals | No dielectric breakdown |
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | Between any contactless terminal and the other terminal | 10000 M Min. |
| Contact Resistance | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA). | Matched terminals, tail end measurement | 30 m MAX. |
| 5. Mechanical Performance / | |||
| Insertion and withdrawal forces | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | Insertion: 35 N max. Withdrawal: 2 N min. | |
| Terminal Strength | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | No looseness, damage, etc. Terminal deformation is acceptable. | |
| 6. Durability / | |||
| Life test | Under no load conditions, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | Matching plug, 1000 cycles | Appearance: No obvious change. Contact resistance: less than 50 m. |
| 7. Solderability / | |||
| Resistance to soldering heat | The jack terminal should be dipped in solder. Temperature of solder: 2603. Dip time: 51 seconds. | After test, plastic base should not be deformed and terminals should not fall off. | |
| Solderability | Temperature of solder: 2453C. Time of dip: 30.5 seconds. | Coating of solder area should be more than 95%. | |
| 8. Environment test / | |||
| Cold test | Place the housing for 96 hours at a low temperature of -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test. | Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| Heat test | The housing should be stored at a temperature of 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | (Performance not explicitly stated for Heat Test, but implied to be similar to Cold Test and Humidity Test based on context) | |
| Humidity test | The housing should be stored at a temperature of 403 with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | Appearance: No obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| Temperature Cycling | Place the Jack under the conditions shown below and then place it in the stand at room temperature for 30 minutes. | (Specific conditions not detailed in text) | (Performance not explicitly stated) |
| Salt spray test | Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Wash and dry at room temperature after the experiment. | Appearance: No obvious rust. | |
| 9. Test condition / | |||
| Standard Conditions | Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. | ||
| Doubtful Judgment Conditions | Test and measurement at 201C, relative humidity 63% to 67%, air pressure: 86 kPa to 106 kPa. | ||
| 10. Amendment / | |||
| Procedure | Amendments require negotiation and agreement between the manufacturer and the customer. | ||
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Employee Number:
<300
Ecer Certification：
Verified Supplier
Hefei Purple Horn E-Commerce Co., Ltd. is a professional company focus on integrated circuit ic business. Hefei Purple Horn E-Commerce Co., Ltd. will also responsible with exporting and logistic business. there is professional factory Beijing Silk Road which focus on desigining and manufacture. Fou... Hefei Purple Horn E-Commerce Co., Ltd. is a professional company focus on integrated circuit ic business. Hefei Purple Horn E-Commerce Co., Ltd. will also responsible with exporting and logistic business. there is professional factory Beijing Silk Road which focus on desigining and manufacture. Fou...
Get in touch with us
Leave a Message, we will call you back quickly!