Shenzhen ECER Network Technology Co., Ltd.
| Description | Through Hole Circular Connector Assemblies RoHS |
| Mfr. Part # | XLR-11W-N3B |
| Package | Through Hole |
| Model Number | XLR-11W-N3B |
View Detail Information
Explore similar products
Durable RoHS Compliant Connector CAX XLR-19ZP-7P Suitable for Electronic
Amphenol PT06E-12-4P SR Connector Designed for Communications Geophysical and
Panel Mount Socket Connector CAZN M12-P8A-GPFM12 European Standard M12 Series
Rear Mount Socket Plastic Waterproof Connector Pin Type PCB Board Mount CAZN E7T
Product Specification
| Description | Through Hole Circular Connector Assemblies RoHS | Mfr. Part # | XLR-11W-N3B |
| Package | Through Hole | Model Number | XLR-11W-N3B |
This specification applies to XLR jack (Combo) which is used in electronic products. The connector is designed for speaker socket connections.
| Item | Property | Test Condition | Performance |
| 2. Rated / | Practical temperature range | -30to +80 | |
| Humidity range | 85% RH.MAX. | ||
| Preservation temperature range | -10to +40 | Humidity range85% RH.MAX. Around air free of acid, alkali or other corrosive gases. Storage period not exceed 180 Days. | |
| Rated voltage and current(MAX.) | 50V AC , 3A(Type A) 7.5A(Type B) | ||
| 4. Electrical efficiency / | Withstand Voltage | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute | No dielectric breakdown shall occur. |
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 10000 M Min. | |
| Contact Resistance | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA) | 30 m MAX. | |
| 5. Mechanical Performance / | Insertion and withdrawal forces | Rate of insertion/withdrawal: 2 mm/s Mating of complete connectors without the effect of any latching or retaining device | XLR: Insertion: 35 N max. Withdrawal: 2 N min. JACK: Insertion: 40 N max. Withdrawal: 5 N min. |
| Terminal Strength | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | No looseness, damage, etc., but terminal deformation is acceptable. | |
| Durability / | Life test: Under no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | No obvious change in appearance, destruction. Contact resistance: less than 50 m. | |
| 7. Solderability / | Resistance to soldering heat | The jack terminal should be dipped in solder: Temperature of solder: 2603. Dip time: 51 seconds. | After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base. |
| Solderability | Temperature of solder: 2453C. Time of dip: 30.5 seconds. | Coating of solder area should be more than 95% | |
| 8. Environment test / | Cold test | Place the housing for 96 hours at -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test. | No obvious change in appearance. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. |
| Heat test | The housing should be stored at 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | ||
| Humidity test | The housing should be stored at 403 with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | No obvious change in appearance. Contact resistance: 50mmax. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| Temperature Cycling | Place the Jack under the conditions shown below and then place it in the stand at room temperature for 30 minutes. | ||
| Salt spray test | Temperature: 35 2 Solution: 5 1% Spray time: 24 hours. Wash and dry at room temperature after the experiment. | No obvious rust in the appearance. | |
| 9. Test condition / | Unless otherwise specified, test and measurement temperature is between 15C and 35C, relative humidity is between 25% and 85%, and atmospheric pressure is between 86 kPa and 106 kPa. If doubts arise, test at 201C, 63% to 67% relative humidity, and 86 kPa to 106 kPa atmospheric pressure. | ||
| 10. Amendment / | Amendments require negotiation and agreement between the manufacturer and the customer. | ||
| 12. XLR JACK (Combo) TYPE /XLR | Type A, Type B | ||
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification：
Verified Supplier
Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability... Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability...
Get in touch with us
Leave a Message, we will call you back quickly!