Shenzhen ECER Network Technology Co., Ltd.
| Description | Through Hole Circular Connector Assemblies RoHS |
| Mfr. Part # | XLR-04-3-N3B |
| Package | Through Hole |
| Model Number | XLR-04-3-N3B |
View Detail Information
Explore similar products
Durable RoHS Compliant Connector CAX XLR-19ZP-7P Suitable for Electronic
Amphenol PT06E-12-4P SR Connector Designed for Communications Geophysical and
Panel Mount Socket Connector CAZN M12-P8A-GPFM12 European Standard M12 Series
Rear Mount Socket Plastic Waterproof Connector Pin Type PCB Board Mount CAZN E7T
Product Specification
| Description | Through Hole Circular Connector Assemblies RoHS | Mfr. Part # | XLR-04-3-N3B |
| Package | Through Hole | Model Number | XLR-04-3-N3B |
This specification applies to XLR jack connectors used in electronic products. It details the electrical, mechanical, durability, and environmental performance characteristics of the XLR jack, ensuring reliable operation within specified temperature and humidity ranges.
| Item | Property | Test Condition | Performance |
| 2. Rated / | |||
| Practical temperature range | -30 to +80 | ||
| Humidity range | 85% RH.MAX. | ||
| Preservation temperature range | -10 to +40 | ||
| Preservation humidity range | 85% RH.MAX. | ||
| Storage conditions | Ambient air free of acid, alkaline, or other corrosive gases. Storage period not exceeding 180 days. | ||
| Rated voltage and current (MAX.) | 50V AC, 6A | ||
| Appearance | No scratches, soil, rust, or discoloration on the surface. | ||
| 4. Electrical efficiency / | |||
| Withstand Voltage | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur. | ||
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 10000 M Min. | |
| Contact Resistance | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA). | 30 m MAX. | |
| 5. Mechanical Performance / | |||
| Insertion and withdrawal forces | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | Insertion: 35 N max. Withdrawal: 2 N min. | |
| Terminal Strength | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | There is no looseness, damage, etc., but terminal deformation is acceptable. | |
| 6. Durability / | |||
| Life test | Under no load condition, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | No obvious change in appearance, destruction. Contact resistance: less than 50 m. | |
| 7. Solderability / | |||
| Resistance to soldering heat | Jack terminal dipped in solder: Temperature 2603, Dip time 51 seconds. | After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base. | |
| Solderability | Solder temperature: 2453C. Time of dip: 30.5 seconds. | Coating of solder area should be more than 95%. | |
| 8. Environment test / | |||
| Cold test | Housing placed for 96 hours at -30 3 C. Then placed under standard atmospheric conditions for 1 hour and tested. | Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| Heat test | Housing stored at 802 for 96 hours. Then subjected to standard atmospheric conditions for 1 hour and tested. | ||
| Humidity test | Housing stored at 403 with relative humidity of 90% ~ 95% for 96 h. Then subjected to standard atmospheric conditions for 1 hour and tested. | Appearance: No obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| Temperature Cycling | Jack placed under specified conditions, then placed at room temperature for 30 minutes. | ||
| Salt spray test | Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Washed and dried at room temperature after the experiment. | Appearance: No obvious rust. | |
| 9. Test condition / | |||
| Standard Test Conditions | Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. For doubtful judgments: 201C, 63% to 67% RH, 86 kPa to 106 kPa. | ||
| 10. Amendment / | |||
| Specification Amendments | Must be negotiated and agreed by the manufacturer and the customer before proceeding. | ||
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification：
Verified Supplier
Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability... Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability...
Get in touch with us
Leave a Message, we will call you back quickly!