Shenzhen ECER Network Technology Co., Ltd.
| Description | Through Hole Circular Connector Assemblies RoHS |
| Mfr. Part # | XLR-04WP-1 |
| Package | Through Hole |
| Model Number | XLR-04WP-1 |
View Detail Information
Explore similar products
Durable RoHS Compliant Connector CAX XLR-19ZP-7P Suitable for Electronic
Amphenol PT06E-12-4P SR Connector Designed for Communications Geophysical and
Panel Mount Socket Connector CAZN M12-P8A-GPFM12 European Standard M12 Series
Rear Mount Socket Plastic Waterproof Connector Pin Type PCB Board Mount CAZN E7T
Product Specification
| Description | Through Hole Circular Connector Assemblies RoHS | Mfr. Part # | XLR-04WP-1 |
| Package | Through Hole | Model Number | XLR-04WP-1 |
This specification applies to XLR jack connectors used in electronic products. It details the electrical, mechanical, durability, and environmental performance characteristics of the product.
| Item | Property | Test Condition | Performance |
| 2. Rated / | Practical temperature range | -30 to +80 | N/A |
| Humidity range | 85% RH.MAX. | N/A | |
| Preservation temperature range | -10 to +40 | N/A | |
| Humidity range (Preservation) | 85% RH.MAX. | N/A | |
| Storage Condition | Around air without acid, alkaline or other corrosive gases. Storage period not exceed 180 days. | N/A | |
| Rated voltage and current (MAX.) | 50V AC , 6A | N/A | |
| Appearance | No scratches, soil, rust or discoloration on the surface. | N/A | |
| 3. Construction / | Outline And Dimension | Should match the attachment drawing. | N/A |
| Part And Material | Should be consistent with the material list specifications. | N/A | |
| 4. Electrical efficiency / | Withstand Voltage | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur. | N/A |
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 10000 M Min. | |
| Contact Resistance | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA). | 30 m MAX. | |
| 5. Mechanical Performance | Insertion and withdrawal forces | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. Insertion: 35 N max. Withdrawal: 2 N min. | N/A |
| Terminal Strength | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. There is no looseness, damage, etc., but the terminal deformation is acceptable. | N/A | |
| 6. Durability / | Life test | Under the condition of no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | Appearance no obvious change, destruction. Contact resistance: less than 50 m. |
| 7. Solderability / | Resistance to soldering heat | The jack terminal should be dipped in solder. Temperature of solder: 2603. Dip time: 51 seconds. After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base. | N/A |
| Solderability | Temperature of solder: 2453C. Time of dip: 30.5 seconds. Coating of solder area should be more than 95%. | N/A | |
| 8. Environment test / | Cold test | Place the housing for 96 hours at a low temperature of -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test. | Appearance no obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. |
| Heat test | The housing should be stored at a temperature of 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | N/A | |
| Humidity test | The housing should be stored at a temperature of 403 with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | Appearance no obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| Temperature Cycling | Place the Jack under the conditions shown below and then place it in the stand at room temperature for 30 minutes. | N/A | |
| Salt spray test | Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Wash and dry it at room temperature after the experiment. | Appearance no obvious rust. | |
| 9. Test condition / | Standard Test Conditions | Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. For judgment doubts: 201C, relative humidity 63% to 67%, air pressure: 86 kPa to 106 kPa. | N/A |
| 10. Amendment / | Amendment Process | Amendments require negotiation and agreement by the manufacturer and the customer. | N/A |
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification：
Verified Supplier
Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability... Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability...
Get in touch with us
Leave a Message, we will call you back quickly!