Shenzhen ECER Network Technology Co., Ltd.
| Description | Through Hole Circular Connector Assemblies RoHS |
| Mfr. Part # | XLR-25W-N3B |
| Package | Through Hole |
| Model Number | XLR-25W-N3B |
View Detail Information
Explore similar products
Durable RoHS Compliant Connector CAX XLR-19ZP-7P Suitable for Electronic
Amphenol PT06E-12-4P SR Connector Designed for Communications Geophysical and
Panel Mount Socket Connector CAZN M12-P8A-GPFM12 European Standard M12 Series
Rear Mount Socket Plastic Waterproof Connector Pin Type PCB Board Mount CAZN E7T
Product Specification
| Description | Through Hole Circular Connector Assemblies RoHS | Mfr. Part # | XLR-25W-N3B |
| Package | Through Hole | Model Number | XLR-25W-N3B |
This specification applies to XLR jacks used in electronic products. The product is designed for a practical temperature range of -30 to +80 and a humidity range of 85% RH.MAX. It has a rated voltage and current of 50V AC and 6A respectively. The appearance should be free from scratches, soil, rust, or discoloration.
| Item | Property | Test Condition | Performance |
| Rated / | Practical temperature range | -30 to +80 | |
| Humidity range | 85% RH.MAX. | ||
| Preservation Temperature | Range | -10 to +40 | |
| Humidity range | 85% RH.MAX. | ||
| Rated voltage and current(MAX.) | 50V AC , 6A | ||
| Appearance | No scratches, soil, rust or discoloration on the surface. | ||
| Electrical efficiency / | Withstand Voltage / | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute | No dielectric breakdown shall occur. |
| Insulation Resistance / | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 10000 M Min. | |
| Contact Resistance / | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA) | 30 m MAX. | |
| Mechanical Performance / | Insertion and withdrawal forces / | Rate of insertion/withdrawal: 2 mm/s | Insertion: 35 N max. Withdrawal: 2 N min. |
| Terminal Strength / | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | There is no looseness, damage, etc., but the terminal deformation is acceptable. | |
| Durability / | Life test / | Under the condition of no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | Contact resistance: less than 50 m. Appearance: No obvious change. |
| Resistance to soldering heat / | Temperature of solder: 2603. Dip time: 51 seconds. | After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base. | |
| Solderability / | Solderability / | Temperature of solder: 2453C. Time of dip: 30.5 seconds. | Coating of solder area should be more than 95% |
| Environment test / | Cold test / | Place the housing for 96 hours at a low temperature of -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test. | Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. |
| Heat test / | The housing should be stored at a temperature of 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | ||
| Humidity test / | The housing should be stored at a temperature of 403 with relative humidity of 90% ~ 95% for 96 h. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | Appearance: No obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| Salt spray test / | Temperature: 35 2 Solution: 5 1% Spray time: 24 hours | No obvious rust in the appearance. | |
| Test condition / | Unless otherwise specified, the test and measurement temperature is between 15 C and 35 C, the relative humidity is between 25% and 85%, and the atmospheric pressure is between 86 kPa and 106 kPa. |
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification：
Verified Supplier
Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability... Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability...
Get in touch with us
Leave a Message, we will call you back quickly!