Shenzhen ECER Network Technology Co., Ltd.
| Description | Through Hole Circular Connector Assemblies RoHS |
| Mfr. Part # | XLR-26A-6P |
| Package | Through Hole |
| Model Number | XLR-26A-6P |
View Detail Information
Explore similar products
Durable RoHS Compliant Connector CAX XLR-19ZP-7P Suitable for Electronic
Amphenol PT06E-12-4P SR Connector Designed for Communications Geophysical and
Panel Mount Socket Connector CAZN M12-P8A-GPFM12 European Standard M12 Series
Rear Mount Socket Plastic Waterproof Connector Pin Type PCB Board Mount CAZN E7T
Product Specification
| Description | Through Hole Circular Connector Assemblies RoHS | Mfr. Part # | XLR-26A-6P |
| Package | Through Hole | Model Number | XLR-26A-6P |
This specification applies to XLR jack (Combo) which is used in electronic products. It is designed for applications requiring reliable audio signal connections.
| Item | Property | Test Condition | Performance |
| 2. Rated / | |||
| Practical temperature range | -30 to +80 | ||
| Humidity range | 85% RH.MAX. | ||
| Preservation temperature range | -10 to +40 | ||
| Preservation humidity range | 85% RH.MAX. | ||
| Storage condition | Surrounding air without acid, alkaline or other corrosive gases. Storage period not exceeding 180 days. | ||
| Rated voltage and current (MAX.) | Type A: 50V AC, 3A | ||
| Rated voltage and current (MAX.) | Type B: 50V AC, 7.5A | ||
| Appearance | No scratches, soil, rust or discoloration on the surface. | ||
| 4. Electrical efficiency / | |||
| Withstand Voltage | Withstand AC 1500V (50/60Hz RMS) between two non-contact terminals for 1 minute. No dielectric breakdown shall occur. | ||
| Insulation Resistance | Apply 500V DC between any contactless terminal and the other terminal, with an insulation gauge and last for 1 minute 5 seconds. | 10000 M Min. | |
| Contact Resistance | Take a pair of matched terminals and measure the tail end of each terminal (voltage maximum 20mV, current maximum 100mA). | 30 m MAX. | |
| 5. Mechanical Performance / | |||
| Insertion and withdrawal forces | Rate of insertion/withdrawal: 2 mm/s. Mating of complete connectors without the effect of any latching or retaining device. | XLR: Insertion: 35 N max. Withdrawal: 2 N min. JACK: Insertion: 40 N max. Withdrawal: 5 N min. | |
| Terminal Strength | Every terminal should be capable of withstand a force of 0.5 kgf for 10 seconds. | No looseness, damage, etc., but terminal deformation is acceptable. | |
| 6. Durability / | |||
| Life test | Under no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times in total, at a frequency of 5 times per minute. | Appearance: No obvious change, destruction. Contact resistance: less than 50 m. | |
| 7. Solderability / | |||
| Resistance to soldering heat | The jack terminal should be dipped in solder: Temperature: 2603. Dip time: 51 seconds. | After the test, the plastic base should not be deformed and the terminals should not fall off the plastic base. | |
| Solderability | Temperature of solder: 2453C. Time of dip: 30.5 seconds. | Coating of solder area should be more than 95%. | |
| 8. Environment test / | |||
| Cold test | Place the housing for 96 hours at -30 3 C. Then, place it under standard atmospheric conditions for 1 hour and test. | Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| Heat test | The housing should be stored at 802 for 96 hours. Then it should be subjected to standard atmospheric conditions for 1 hour and test. | ||
| Humidity test | Store at 403 with relative humidity of 90% ~ 95% for 96 h. Then subject to standard atmospheric conditions for 1 hour and test. | Appearance: No obvious change. Contact resistance: 50m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V. | |
| Temperature Cycling | Place the Jack under specified conditions and then place it in the stand at room temperature for 30 minutes. | ||
| Salt spray test | Temperature: 35 2. Solution: 5 1%. Spray time: 24 hours. Wash and dry at room temperature after the experiment. | Appearance: No obvious rust. | |
| 9. Test condition / | |||
| Standard conditions | Test and measurement temperature: 15C to 35C, relative humidity: 25% to 85%, atmospheric pressure: 86 kPa to 106 kPa. | ||
| Doubtful conditions | Test and measurement at 201C, relative humidity 63% to 67%, air pressure: 86 kPa to 106 kPa. | ||
| 10. Amendment / | |||
| Procedure | Amendments require negotiation and agreement between manufacturer and customer. | ||
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification：
Verified Supplier
Your Trusted Source for Integrated CircuitShenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability a... Your Trusted Source for Integrated CircuitShenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability a...
Get in touch with us
Leave a Message, we will call you back quickly!