Shenzhen ECER Network Technology Co., Ltd.
| Y-Width of Bottom Edge on Board | 4.25mm |
| Pins Structure | 1x2P |
| Reference Series | GH |
| Contact Plating | 锡 |
| Contact Material | 磷青铜;LCP |
| Operating Temperature | -25℃~+85℃ |
| Flame Retardant Rating | UL94V-0 |
| Pitch | 1.25mm |
| Voltage Rating (Max) | 50V |
| Number of PINs Per Row | 2 |
| Number of Rows | 1 |
| X-Length of Bottom Edge on Board (Spacing Line) | 5.8mm |
| Z-Height of the Board | 4.05mm |
| Row Spacing | - |
| Mounting Type | 立贴 |
| Description | Connector Header 2 position 1.25mm Pitch 1A Surface Mount,Vertical -25℃~+85℃ |
| Mfr. Part # | GH125-S02CCA-00 |
| Package | SMD,P=1.25mm |
| Model Number | GH125-S02CCA-00 |
View Detail Information
Explore similar products
Precision wafer connector HDGC HDGC1254WR-S-6P featuring 1.25MM pitch and 90
PCB layout part HCTL HC-0.8-6PLT designed for temperature range minus 25 to plus
2.54mm Pitch Single Row Pin Header Connector OUPIIN 2011H-1X40G01SB Straight
PCB mount horizontal SMT connector 1.0mm pitch JUSHUO SHB10-S03DCA-00 with
Product Specification
| Y-Width of Bottom Edge on Board | 4.25mm | Pins Structure | 1x2P |
| Reference Series | GH | Contact Plating | 锡 |
| Contact Material | 磷青铜;LCP | Operating Temperature | -25℃~+85℃ |
| Flame Retardant Rating | UL94V-0 | Pitch | 1.25mm |
| Voltage Rating (Max) | 50V | Number of PINs Per Row | 2 |
| Number of Rows | 1 | X-Length of Bottom Edge on Board (Spacing Line) | 5.8mm |
| Z-Height of the Board | 4.05mm | Row Spacing | - |
| Mounting Type | 立贴 | Description | Connector Header 2 position 1.25mm Pitch 1A Surface Mount,Vertical -25℃~+85℃ |
| Mfr. Part # | GH125-S02CCA-00 | Package | SMD,P=1.25mm |
| Model Number | GH125-S02CCA-00 |
This product acknowledgment document details the specifications for the 1.25mm pitch vertical SMT connector with latch, model GH125-S**CCA-00. It covers standard ratings, packaging, transportation, storage, component materials, electrical characteristics, environmental characteristics, and mechanical properties.
| Item | Specifications | Test Method | Performance Requirements |
| Standard Rating | |||
| Rated voltage | 50V | ||
| Rated current | 1.0A AC/DC | ||
| Operating temperature range | -2585 | ||
| Operating humidity range | Relative humidity is below 90% | ||
| Component Material | |||
| Part name | Model | Material | |
| Base | GH LCP E130i | ||
| Pin | GH Phosphor copper | ||
| Stator | GH Phosphor copper | ||
| Electrical Characteristics | |||
| Contact resistance | Plug in the connector and test it with a contact resistance meter to measure both terminals of the connector Form a closed loop between. | 20m Max | |
| Insulation resistance | Plug in the connector and apply 100V DC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute. | 500M Min | |
| Withstand voltage | Plug in the connector and apply 500V AC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute. | No breakdown and flashover | |
| Environmental Characteristics | |||
| Heating test | Put the plug connector in the environment of +852 for 96H, take it out and put it in the normal environment for 1~2H before testing. | Appearance: appearance without damage; Contact resistance: 60m Max | |
| Cold tolerance test | The plug connector was placed in the environment with the temperature of -252 for 96H, and was taken out and placed in the normal environment for 1~2H before being tested. | Appearance: appearance without damage; Contact resistance: 60m Max | |
| Moisture resistance test | Place the plug connector in an environment with a temperature of 402 and relative humidity of 90~96%. Last for 96H, after the test, take it out and put it in the normal environment for 1~2H before the test. | Appearance: appearance without damage; Insulation resistance: 60M min; Withstand voltage: 250V AC/minute MIN | |
| Temperature cycle | Put the test samples into the high and low temperature test chamber, and adjust the temperature according to the following steps: A. Place for 30 minutes under the constant temperature of -253 B. Place at room temperature for 1 hour C. Place for 30 minutes at a constant temperature of +853 D. Place at room temperature for 1 hour From a to d is a cycle period, a total of 5 cycles are carried out, and 2H is recovered in the normal environment Check later. | Appearance: no abnormality; Contact resistance: 60m Max | |
| Salt Spray Test | The test sample was suspended from the top of the test box, and the concentration of (51)% Sodium Chloride Solution was continuously sprayed with 24H. After testing, the surface precipitates were lightly washed with flowing steaming water, then the 1~2H was rechecked at normal temperature. | Appearance: no damage or corrosion (hardware should not expose the bottom metal of serious corrosion: use pre-plating The blanking surface is allowed to have a slight corrosion that does not affect its performance. Contact resistance: 60m Max | |
| Weldability | Dip the welded part of the test sample into 2605 tin solution and hold 2.50.5 seconds. | Tin area above 95% | |
| Soldering resistance | Place the connector on the PCB, and then reflow the product through 2605 Or wave soldering for 5 1s. | 1. Plastic parts shall be free from obvious deformation, damage and blistering. 2. The electrical characteristics must meet the specifications. | |
| Mechanical Properties | |||
| Pin fixing force | Fix the pin holder on the drawing machine and apply force on the front end of the pin at a rate of 253mm per minute until the pin is withdrawn from the pin holder. | Single pin 5N min | |
| Terminal retention in plastic parts | The terminal shall be matched with the hole seat, and at the rate of 253mm per minute along the conductor direction, the force that the terminal is pulled out of the socket. | Single terminal: 7N min | |
| Mechanical life | Under no power on state, plug and unplug 30 times at the speed of 10 times / min. | Contact resistance: 80m Max | |
| Terminal crimp lead Line strength | The terminals are pressed into wire at 253mm per minute The axial pullout rate of | 26AWG wire 17.8N; 28AWG wire 8.9N; 30AWG wire 4.4N; 32AWG wire 2.2N | |
| Insertion pull out force | (1) Fit the hole seat and the terminal, and conduct the insertion and removal test on the same axis with the needle seat. Remove the lock of the hole seat (test speed: 20 5mm) minute during the test | Insertion force 2N(Per pin); Pullout force 0.3N(Per pin) | |
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Total Annual:
10000000-50000000
Employee Number:
300~500
Ecer Certification：
Verified Supplier
Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability... Your Trusted Source for Integrated Circuit Shenzhen ECER Network Technology Co., Ltd. is a professional company focus on integrated circuit ic business. ECER connects buyers worldwide with verified manufacturers across 40+ industries. Every component sourced with precision, quality, and reliability...
Get in touch with us
Leave a Message, we will call you back quickly!