ELAU VIA0702D22A0000 PacDrive M iSH070 Integrated Servo Motor

Product Specification

ELAU VIA0702D22A0000 PacDrive M iSH070 Integrated Servo Motor

The ELAU VIA0702D22A0000 is an iSH070 integrated servo motor for installed legacy PacDrive M motion systems. Its corresponding technical type is iSH070/60017/0/0/00/0/10/10/00. The assembly combines a synchronous servo motor, position feedback and integrated drive electronics, helping maintenance teams identify the complete replacement unit rather than only the motor body.

This discontinued / legacy genuine spare-part listing is intended for maintenance, planned spare-part purchasing and recovery of existing machine axes. Supply is assessed against the actual unit and the complete identification on its nameplate. Please request a quotation with your full reference and required condition; publication of this page does not confirm present stock.

Technical Identification and Configuration

The figures above identify the documented base configuration. Standstill torque and rated torque describe different operating points; the standstill value must not be treated as continuous torque at rated speed. Operating limits depend on ambient temperature, mounting, load cycle and the original machine design. Confirm the delivered unit's nameplate and hardware version before using these figures for a replacement decision.

What Makes VIA0702D22A0000 Different?

This reference specifies a smooth shaft, multi-turn feedback, a shaft sealing ring and no holding brake. These options affect coupling fit, position referencing, shaft-side protection and brake wiring. A product with the same iSH070/60017 base designation can still have a different full configuration. Please retain every character in VIA0702D22A0000 when placing an inquiry.

This configuration does not include a holding brake. An application requiring a brake needs a separate engineering assessment; the absence of a brake must not be overlooked when matching an installed axis. The shaft seal provides the documented sealed shaft-side configuration. Its condition and suitability for the operating environment must be inspected on the actual unit.

Legacy Machine Maintenance

Typical inquiry situations include a failed integrated servo axis, a planned shutdown spare or a replacement requirement identified from an existing PacDrive M machine. The most useful starting point is the original equipment's reference, not an assumed application match. VIA0702D22A0000 should be checked together with the controller, machine project, hybrid cabling and the installed iSH power and distribution arrangement.

The integrated electronics require the appropriate DC bus and control supply within the original system architecture. This unit should not be selected as a standalone motor to connect directly to an AC mains supply. Firmware, drive configuration, encoder referencing, connector arrangement and commissioning requirements must be reviewed by the responsible maintenance engineer. Similar appearance or torque alone does not establish interchangeability.

Information to Send for a Quote

• Full commercial reference: VIA0702D22A0000, and a clear photograph of the complete nameplate.
• Technical type: iSH070/60017/0/0/00/0/10/10/00, serial number, hardware revision and any readable firmware information.
• Photographs of the shaft, connectors and installed axis, including details of the existing coupling and cabling.
• Quantity, acceptable condition, required delivery date and destination country.
• Whether the requirement is a replacement for a failed unit, a maintenance spare or another purpose, together with any condition or documentation requirements.

Condition, completeness, visible identification and available inspection information are confirmed for the proposed unit before quotation. Accessories, cables and additional modules are included only when specifically listed in the quotation. Any request for an alternative reference needs separate verification against the original machine; this page does not promise automatic compatibility.

Ordering, Price and Dispatch

Minimum order: 1 piece. Indicative price: EUR 4898 per piece, estimated from a related model and subject to confirmation of the actual unit, condition and quotation. Freight, import charges and any additional services are agreed separately. The displayed amount is a reference price rather than a confirmed offer for an identified unit.

Supply planning: up to 10 pieces per month, subject to actual sourcing and availability. When an in-stock unit is confirmed, dispatch is normally within one week after the order and payment arrangements are agreed. For non-stock sourcing, lead time is negotiated separately. Request current availability, condition and the final price for VIA0702D22A0000 before placing an order.

DF Automatic handles inquiries for legacy ELAU PacDrive spare parts. No manufacturer authorization, fixed inventory, guaranteed interchangeability or unverified warranty term is represented by this listing.