Ecer asks for your consent to use your personal data to:
Personalised advertising and content, advertising and content measurement, audience research and services development
Store and/or access information on a device
Your personal data will be processed and information from your device (cookies, unique identifiers, and other device data) may be stored by, accessed by and shared with 135 TCF vendor(s) and 65 ad partner(s), or used specifically by this site or app.
Some vendors may process your personal data on the basis of legitimate interest, which you can object to by do not consent. Contact our platform customer service, you can also withdraw your consent.
{"title":"Rexroth Original German Quantitative High-Pressure Hydraulic Gear Pump with 28cc","imgUrl":"https:\/\/img.chinax.com\/nimg\/18\/b4\/95207730f3b799eff1119aca8867-200x200-1\/rexroth_original_german_quantitative_high_pressure_hydraulic_gear_pump_with_28cc_140cc_displacement.jpg","attrs":{"Brand Name":"Rexroth","Model Number":"PGH4-2X\/025LE11VU2 PGH4-2X\/025LR11VU2 PGH4-2X\/032RE11VU2 PGH4-2X\/032RE11VE4 PGH4-2X\/032RR11VU2","Certification":"ISO","Place of Origin":"German"}}
What is the displacement and pressure rating of this pump?
The geometric displacement is 8.0 cm³/rev. It has a maximum continuous working pressure of 250 bar, an intermittent pressure of 280 bar, and a peak pressure of 300 bar.
What type of shaft and port connection does this model have?
This model (RAB) features a straight cylindrical shaft (Ø18 mm) with a keyway. The port connection is Pipe Thread (ISO 228-1 / BSP), which is different from the metric threaded or flanged ports found in other AZPF models.
What is the rotation direction?
Clockwise rotation when viewed from the shaft end.
Installation & Commissioning
What are the critical installation requirements?
Shaft Alignment: Use a flexible coupling. Radial runout should be < 0.1 mm, angular error < 1 degree. Rigid connections cause bearing failure.
Suction Conditions: Inlet absolute pressure must be ≥ 0.7 bar to prevent cavitation. For this displacement pump, ensure the suction line is short and direct.
Priming:Never run the pump dry. Fill the housing with clean oil before the first start.
How should the case drain port be connected?
The drain line must connect directly to the tank (no valves/filters), below the fluid level but above the pump centerline. Backpressure must not exceed 1 bar.
Operation & Troubleshooting
The pump is very noisy. What is the cause?
Noise is usually cavitation (whining) or aeration (crackling).
Cavitation: Check for clogged inlet filters, high oil viscosity, or low oil level.
Aeration: Check for air leaks in the suction line.
Mechanical Noise: Check for shaft misalignment or worn bearings.
How do I calculate the actual flow output?
Theoretical flow = 8.0 (cm³/rev) × Speed (rpm) / 1000. Actual flow will be 5-10% lower due to internal leakage. A drop of more than 15% indicates significant wear.
The pressure does not reach the rated value. What is wrong?
Common causes include:
Internal Wear: Increased clearance between gears and side plates.
System Leakage: Check relief valves and actuators.
Low Motor Speed or incorrect system settings.
Maintenance
What type of oil and cleanliness are required?
Use ISO VG 32/46/68 mineral-based oils (HL, HLP). The oil cleanliness must be NAS Class 9 or cleaner (ISO 4406 18/16/13) for long bearing life.
Can I repair this pump myself?
Not recommended for critical applications. While seals can be replaced, rebuilding the precision sliding bearings and pressure-compensated side plates requires special tools and testing. An exchange unit is often safer.
What is the expected service life?
Under correct conditions (clean oil, proper viscosity, rated load), the B10 life can reach several thousand hours. Oil contamination is the primary cause of premature failure.
Disclaimer: This data is based on standard Rexroth AZPF series documentation. Always refer to the official datasheet (RE 10 250) for your specific application and safety guidelines.
Company Details
Bronze Gleitlager
,
Bronze Sleeve Bushings
and
Graphite Plugged Bushings
from Quality China Factory
Business Type:
Manufacturer,Exporter
Total Annual:
1 million-10 millon
Employee Number:
>50
Ecer Certification：
Verified Supplier
Quanzhou Yisenneng Hydraulic Electromechanical Equipment Co., Ltd. has been established for many years and has now developed into an international trading company supplying various hydraulic machinery parts, oil pumps and valves. We are one of the few Chinese companies with multiple products and cha... Quanzhou Yisenneng Hydraulic Electromechanical Equipment Co., Ltd. has been established for many years and has now developed into an international trading company supplying various hydraulic machinery parts, oil pumps and valves. We are one of the few Chinese companies with multiple products and cha...
