Surfboard Mosfet Marine Brushless ESC HV 22S 500A OPTO For Boat

Product Specification

Fliermodel High Powerful Surfboard Waterproof Brushless ESC HV 22S 500A Mosfet For Boat

Basic information:

Feature:

1. Design for Air, more functions.
2. Battery voltage from 4S to 120V for super high voltage version.
3. Two way communication while connecting it with computer.
4. Firmware can be upgraded by user.
5. Simply set function value by Prog-Box or by PC via USB link wire.
6. Li-MH/Li-Po, Ne-Cd/Ne-mH, LiFe battery can be use.
7. Enables setting the voltage per cell for the point at which the controller’s cut off circuitry engages. Li-MH/Li-Po from 2.0-3.6V,Ne-Cd/Ne-mH 0.4-1.0V,LiFe from2.2-2.8V .
8. Timing settings may be adjusted (0°-30°)per degree to suit the motor type
9. 3 types of throttle curve .
10. Automatically detection the throttle range or can be set a fixed value by manual operation.
11. Auto cut off the power within 3 seconds if no radio signs.
12.Reverse off.

How the ESC to control the motor speed?

Set the required speed with the speed adjustment potentiometer. The sensor measures the actual value of the engine speed through the ring gear on the flywheel and sends it to the controller. The actual value in the controller is compared with the set value. The control line is arranged and enlarged, and the output shaft of the actuator is driven. The fuel pump pin is pulled by adjusting the connecting rod to adjust the oil supply amount, thereby achieving the purpose of maintaining the set rotation speed.

This electronic governor can also choose the size of the unevenness according to the needs of the engine. When the stepless speed regulation is performed, the electronic control system eliminates the difference between the set speed and the actual speed caused by the load change, so that the engine maintains the original set speed. According to the needs of the unit, the unevenness potentiometer can also be adjusted to achieve a satisfactory static adjustment rate of the speed control system.

The electronic governor is also equipped with a variety of accessory devices. According to the needs of the unit, the corresponding accessories can be installed to realize the functions of automatic synchronization, load distribution and load preset.

The electronic governor is characterized by the ability to independently determine the speed regulation characteristics, and to determine the optimum torque characteristics, idle speed characteristics and transition characteristics when all accessories are installed. The electronic dispatcher can adapt to the requirements of different models.

Setting function value:

1. Reverse: On/Off.

2. Timing:0°,1°,2°,3°,4°……30°.

3. Frequency: 8KHz, 16 KHz, 32 KHz.

4. Acceleration: Soft / Medium / Hard.

5. Accumulator type:NiCd/NiMh,Li-Ion/Li-Pol,LiFe.

6. NiCd/NiMH CUTOFF:×0.05,0.4V,0.5V,0.6V,0.7V,0.8V,0.9V,1.0V.×0.05 means the cut off voltage is 5% the voltage while connecting.

7. Number of cells:Auto,2S,3S,4S,5S,6S,7S,8S,9S,10S,11S,12S,16S.

8. LiIo/Pol CUTOFF:2.0V,2.1V,2.2V,2.3V,2.4V,2.5V,2.6V,2.7V,2.8V,2.9V,3.0V,3.1V,3.2V,3.3V,3.4V,3.5V,3.6V.

9. LiFe cutoff:2.2V,2.3V,2.4V,2.5V,2.6V,2.7V,2.8V

10. Cut Off Type::Slow down,Hard. l

11. Power limited forward: Off, 75%, 50%, 25%.

12. Power limited reverse: Off, 75%, 50%, 25%.

13. Delay time when direction convert: 0.25S, 0.5S, 0.75S, 1S, 1.5S, 2S, 3S, 5S.

14. Reverse point:Auto,fixed 1.0mS,fixed 1.1mS,fixed 1.2mS,fixed 1.3mS.

Note:the red mark is the factory default value,you can setting function value by youself.

Notice: Correctly use the anti-spark wires.

The anti-spark wire including a bullet connector and an anti-spark resistor. So you can
separate it into two wires. You must solder another wire on the negative wire of the battery
pack. If you want to connect the ESC to the battery pack, you can connect the red wire of
ESC to the positive wire of the battery at first. Then connect the anti-spark wires well. The
last step is to connect the black wire of ESC to the negative wires of the battery. If do like
that, no spark will be generated, and it will protect the main bullets connector from
damaged
 

Trade Terms:

1.Payment :T/T ,Paypal,West union .

2.Production lead time :5 days for 100-200 pcs ,10days for 200-300pcs .

3.Sample can be delivered within 3 days.

4.Discounts are offered based on order quantities .

5.MOQ: 2 pcs.

Shipping&Return:

1. Items will be shipped within 3 business day after payment completed received.

2. Items are shipped from DHL Express ,UPS ,EMS,, reach most of the countries within 3-7 days respectively.

3. Warranty Period is 2 yrs for this item.

4. If product can not work, or find it as defects within in 7 days after receipt, please contact us, we will replace or refund.

5. All emails will be answered within 1 working day.