Ecer asks for your consent to use your personal data to:
Personalised advertising and content, advertising and content measurement, audience research and services development
Store and/or access information on a device
Your personal data will be processed and information from your device (cookies, unique identifiers, and other device data) may be stored by, accessed by and shared with 135 TCF vendor(s) and 65 ad partner(s), or used specifically by this site or app.
Some vendors may process your personal data on the basis of legitimate interest, which you can object to by do not consent. Contact our platform customer service, you can also withdraw your consent.
387-9432 3879432 Fuel Injector for C9 Engine E330D Excavator Spare Parts
Product Overview
Part Name
Injector
Size (per unit)
20cm x 5cm x 8cm
Approximate Weight
1KG
Product Details
Product Name
Fuel Injector
Part Number
387-9432
Equipment Compatibility
330D Excavators
Type
Engine Parts
Place of Origin
GUANGZHOU
Brand Name
JIAJUE
Minimum Order Quantity
1 Piece
Condition
New
Availability
Rich Stock
Warranty
3 Months
Shipment
Dispatched within 24-48 hours
Product Testing
Related Products
Frequently Asked Questions
Q1: How do I install my fuel injector after purchasing it?
Please refer to the "Step-by-Step Installation Guide" on our product details page, which contains detailed installation instructions.
Q2: What precautions should I take before installing my fuel injector?
The installation environment must be dust-free; lubricate the O-ring with clean machine oil before installation to prevent oil leakage; ensure the O-ring is installed correctly.
Q3: Why is my engine still unusable after replacing the fuel injector?
This is common due to air trapped in the high-pressure oil rail. Cycle the engine in short bursts (no more than 30 seconds) to purge air. It may take several attempts to stabilize pressure.
Q4: Is my device compatible with this part number of fuel injectors?
If unsure about compatibility, please provide your Engine Serial Number (ESN) for free verification.
Q5: How to determine if your fuel injectors need replacing?
Cylinder Cut-out Test: Using diagnostic software (ET), shut off cylinders one by one and observe engine speed fluctuations to locate faulty cylinders.
Fuel Rail Pressure Test: Check for internal leaks preventing system from building critical starting pressure.
Back-leakage Test: Excessive back-leakage indicates severe wear of internal control valve assembly.
Visual Inspection: Inspect fuel injector nozzles for carbon buildup, blockage, or corrosion.
Q6: How long will it take to receive my package after payment?
Delivery time depends on your country, region, and customs clearance. Contact us with your address and postal code for shipping costs and estimated delivery time.
Step-by-Step Installation Guide
Pro-Tip: HEUI (Hydraulic Electronic Unit Injection) systems are extremely sensitive to contamination. A single speck of dust can cause premature failure.
1. Preparation: Clean the injector bores thoroughly. Ensure no carbon debris, old O-rings, or fuel/oil residue at the bottom of the seat. Inspect the injector sleeve for pitting or erosion.
2. Lubrication: Apply clean engine oil to the three O-rings and backup rings. Warning: Never use grease. Only use clean engine oil to ensure seals slide in without tearing.
3. Seating the Injector: Push the injector down firmly by hand until you feel it "seat." Install the hold-down clamp and bolt.
4. Torque Specifications: Tighten the bolt to 30 N⋅m±7 N⋅m (22 lb-ft). Note: Over-tightening can crack the injector body; under-tightening causes combustion gas leakage.
5. Trim Code Programming: Locate the 6-digit alphanumeric code on the top of the injector solenoid. Use ET (Electronic Technician) software to program this code into the ECM for precise fuel delivery synchronization.
Troubleshooting Guide
Issue
Root Cause
Solution
Black Smoke
Poor spray atomization or stuck needle valve causing dripping
Inspect the air filter
Hard Start
Internal leakage in injector leading to insufficient starting oil pressure
Inspect injector O-rings and internal seals
Engine Misfire
Faulty solenoid valve coil or worn internal valve components
Inspect wiring harness connections and replace damaged injectors
Company Profile
Exhibition
Factory Environment
Packaging & Shipping
Product Video
Company Details
Bronze Gleitlager
,
Bronze Sleeve Bushings
and
Graphite Plugged Bushings
from Quality China Factory
Business Type:
Manufacturer,Distributor/Wholesaler,Trading Company
Year Established:
2014
Total Annual:
5000000-8000000
Employee Number:
15~35
Ecer Certification：
Verified Supplier
GUANGZHOU JIJAUE CONSTRUCTION MACHINERY PARTS specializes in R&D and production of diesel high pressure common rail fuel systems and related components. At present, our main products include single-cylinder (air-cooled and water-cooled) common-rail system products, heavy-duty diesel common-rail ... GUANGZHOU JIJAUE CONSTRUCTION MACHINERY PARTS specializes in R&D and production of diesel high pressure common rail fuel systems and related components. At present, our main products include single-cylinder (air-cooled and water-cooled) common-rail system products, heavy-duty diesel common-rail ...
