| Motor Power | 33 kW |
| Productive Capacity | 3 blocks/h |
| Foaming Size | 2100*1800*1000 mm |
| Payment Terms | L/C,T/T |
| Stirring Volume | 15 m³ |
| Stirring Rate | 40 r/min |
| Supply Ability | 3 sets per season |
| Machine Weight | 8000 kg |
| Packaging Details | TO BE DETERMINED |
| Delivery Time | 45 working days after downpayment |
| Model Number | TDP-10 |
| Place of Origin | Qingdao |
| Certification | CE |
| Brand Name | Xinmeiteng |
View Detail Information
Explore similar products
Bonding and steam press molding Regenerative Foam Rebonded Equipment Tripple
Re-Bonding Foam Block Foaming Machine Sponge Making Machine recycled EVA EPE
Rebonding Sponge Foaming Machine
TDPB-A Rebonded Unifoam foam density Square Foam Recycling Foaming Machine
Product Specification
| Motor Power | 33 kW | Productive Capacity | 3 blocks/h |
| Foaming Size | 2100*1800*1000 mm | Payment Terms | L/C,T/T |
| Stirring Volume | 15 m³ | Stirring Rate | 40 r/min |
| Supply Ability | 3 sets per season | Machine Weight | 8000 kg |
| Packaging Details | TO BE DETERMINED | Delivery Time | 45 working days after downpayment |
| Model Number | TDP-10 | Place of Origin | Qingdao |
| Certification | CE | Brand Name | Xinmeiteng |
| High Light | 15 m³ Foam Mixing Tank ,40 r/min Stirring Speed ,Uniform Density Rebond Foam | ||
Density variation in a rebonded block starts in the mixing tank. The TDP-10 stirs a 15 m³ batch at 40 r/min, fills a 2100*1800*1000 mm mould, and runs 3 blocks per hour on a 33 kW drive. Machine weight is 8000 kg, overall size 4000*4000*5400 mm, and the line is CE certified.
A block that is dense at one end and light at the other cannot be sold as one grade. The cause is almost always binder distribution: if the spray does not reach every part of the batch, some shredded foam is coated and some is not. A 15 m³ tank with a 40 r/min stirrer is sized to keep a full batch moving so the binder reaches the whole volume before the fill.
A full mould fill comes from one mix, so the block is one batch rather than a blend of two.
The tank turns the whole batch, so binder reaches the bottom and the walls as well as the centre.
The dosing pump and the mixing time are the two settings that hold the block inside one density grade.
The mixing time is not a formality. Stopping the cycle early leaves part of the batch under-coated, and that shows up as a soft end on an otherwise good block.
Density variation in a rebonded block has three usual sources: uneven binder coverage, uneven shred size, and a fill that separates the mix. Binder coverage is the most common. If the spray is concentrated in one part of the tank, the foam there bonds tightly and the rest of the block is loose.
Shred size matters because the binder coats surface area, not weight. A batch with a wide spread of shred sizes has a wide spread of surface area, so the same binder quantity produces a different bond from particle to particle. Keeping the shred size consistent is the cheapest way to keep the block density consistent.
The fill is the third source. A batch that sits after mixing can separate, with heavier wetted foam settling. Filling promptly after the mix, in one pass, is why the tank volume and the mould volume are matched on this line.
| Parameter | Value |
|---|---|
| Model | TDP-10 |
| Foaming size | 2100*1800*1000 mm |
| Stirring volume | 15 m³ |
| Stirring rate | 40 r/min |
| Productive capacity | 3 blocks/h |
| Motor power | 33 kW |
| Machine weight | 8000 kg |
| Overall dimension | 4000*4000*5400 mm |
| Certification | CE |
| Symptom | Likely cause | Action |
|---|---|---|
| Block density uneven | Mixing time too short or binder dosing uneven | Extend the mixing cycle, check the dosing pump and spray pattern |
| Block collapses after demould | Binder ratio too low for the shredded foam | Check the binder ratio and give the block its full cure time |
| Foam not bonding in the core | Shredded foam too coarse or binder coverage poor | Reduce shred size, check spray coverage across the tank |
| Block sticks in the mould | Release agent missed or worn off | Re-apply release agent and check the mould surface |
| Output below 3 blocks per hour | Cure time or mould staging delay | Stage moulds so filling does not wait for demoulding |
| Drive trips under load | Mould over-filled or drive fault | Cut the fill weight, check motor current against the 33 kW rating |
Foaming faults show up after demoulding, when the block is already made. Check the mix and the binder dosing before the fill, and one wasted batch is avoided.
Each recipe should have a written card: shred size, batch weight, binder quantity, mixing time and cure time. Operators should work from the card rather than from memory, because a small change in binder quantity is invisible until the block is cut.
Binder handling and ventilation are the safety items. Keep the dosing area ventilated, keep containers closed, and never demould a block before its cure time to gain output.
Clean the tank at the end of a run. Binder build-up on the tank wall reduces the effective volume and changes the mixing pattern, which shows up as density variation long before anyone suspects the tank.
Check the stirrer blades and the spray nozzle weekly. A worn blade leaves a dead zone at the bottom of the tank, and a partly blocked nozzle leaves a dry patch in the batch. Both are cheap to fix and expensive to ignore.
The line ships in export packing with the tank, mould station and panel separated and braced. At 8000 kg and 4000*4000*5400 mm, confirm the container plan and the receiving access before the shipment date.
Delivery is 45 working days after downpayment, payment by T/T or L/C, minimum order one set. Installation guidance and remote commissioning support are included.
A: 15 m³, which fills the 2100*1800*1000 mm mould from one batch.
A: 40 r/min, run for the full mixing time so the binder reaches the whole batch.
A: By binder quantity, shred size and mixing time, all recorded on a recipe card.
A: 3 blocks per hour on a 33 kW drive, machine weight 8000 kg.
A: Measure the top, bottom and both ends of the first block, not just the middle.
Tell us the foam type, block or roll size, target sheet thickness and expected output per shift. We will confirm the machine configuration, quote it and share the delivery schedule. Spare blades, guide parts and remote commissioning support are available with every order.
Company Details
Business Type:
Manufacturer
Year Established:
2002
Total Annual:
1500000-3000000
Employee Number:
50~200
Ecer Certification:
Verified Supplier
XINMEITENG is located in the beautiful seaside city of Qingdao, adjacent to Jinan-Qingdao, Qingyin, Yanqing and Qinghu highways, and connected to Jiaodong International Airport and Qingdao Port Terminal, with a superior geographical location. The company has advanced processing equipment, with more... XINMEITENG is located in the beautiful seaside city of Qingdao, adjacent to Jinan-Qingdao, Qingyin, Yanqing and Qinghu highways, and connected to Jiaodong International Airport and Qingdao Port Terminal, with a superior geographical location. The company has advanced processing equipment, with more...
Get in touch with us
Leave a Message, we will call you back quickly!