Ecer asks for your consent to use your personal data to:
Personalised advertising and content, advertising and content measurement, audience research and services development
Store and/or access information on a device
Your personal data will be processed and information from your device (cookies, unique identifiers, and other device data) may be stored by, accessed by and shared with 135 TCF vendor(s) and 65 ad partner(s), or used specifically by this site or app.
Some vendors may process your personal data on the basis of legitimate interest, which you can object to by do not consent. Contact our platform customer service, you can also withdraw your consent.
The TDP is a single head bevel cutting machine for foam converters who cut angled edges every day. The head swings through the full 45 to 90 degree range on a machined pivot and locks on a calibrated scale, so a chamfer, a wedge and a square edge are three settings of one machine instead of three machines on the floor. A 1500 x 2500 mm feed table carries a full block to the blade, the 1.68 kW drive holds speed in dense rebonded foam, and the 600 mm cutting height covers the block sizes used in mattress, furniture and packaging work.
Core Advantages
Full 45 to 90 degree range on one head: the scale reads the angle at the blade line, and the locking handle holds it through a loaded pass, so the operator sets a chamfer in under one minute and the next part matches it.
Blade line held by a guided carrier: an alloy steel blade at HRC 60 runs in a carrier that keeps tension along its full length, which produces a sealed edge on PU sponge without tearing the cell walls.
1500 x 2500 mm feed table: a full mattress overlay or a furniture profile lies flat through the pass, so the bevel stays straight over the full length of the part.
1.68 kW drive with frequency converter: the feed speed runs from 0 to 30 m/min, slow enough for dense rubber plastic foam and fast enough for soft sponge on a volume order.
600 mm cutting height: blocks up to 600 mm high are bevelled without pre-splitting, which removes one handling step from every batch and one machine from the line.
Welded, stress relieved frame: the frame is machined after welding, so the head stays square after years of loaded passes and the bevel does not drift across a shift.
Technical Specifications
Item
Parameter
Model
TDP
Cutting Angle
45°–90° continuously adjustable
Cutting Height
600 mm
Worktable Size
1500 * 2500 mm
Motor Power
1.68 kW
Cutting Speed
0–30 m/min, frequency converter
Blade
Alloy steel, HRC 60
Machine Weight
1000 kg
Overall Dimension (L * W * H)
2000 * 1000 * 2000 mm
Voltage
380 V / 50 Hz three phase, other voltages on request
Machine Details
Angle head: the cutting head swings on a machined pivot and locks through a calibrated scale, so a 45° chamfer and a 90° square edge are set with the same handle.
Blade carrier: a guided carrier keeps the alloy blade tensioned along its full length, which holds a straight line of cut through dense block foam.
Feed table: 1500 * 2500 mm of flat steel with roller support, so full blocks slide to the blade without lifting.
Frame: welded box section, stress relieved before machining, which keeps the head square after years of loaded passes.
Control box: IP54 enclosure with low voltage circuit, frequency converter and an emergency halt switch on the operator side.
Material Handling Matrix
Material
Working Range / Result
PU sponge, 20–60 kg/m³
up to 600 mm
sealed edge, no cell tearing
Rebonded foam
up to 600 mm
straight bevel on dense blocks
EVA / PE sheet
up to 600 mm stack
clean 45° corner profile
EPE pearl cotton
up to 600 mm
compressed edge without crush marks
Rubber plastic foam
up to 600 mm
square cut at 60° and 90°
Foam laminate with textile
up to 400 mm
edge held true, no fraying
Primary Applications
Mattress and upholstery: chamfered edges on PU overlays, seat cushions and backrest foam, where a true 45° corner decides how the cover sits.
Packaging converters: 45° bevel cuts on EPE and EVA inserts, corner profiles and protective trays that must fit a carton without gaps.
Footwear and gasket production: angled trimming of rubber plastic foam soles, seals and insulation strips in short and medium runs.
Filtration and cleaning products: wedge cutting of sponge blocks for filter pads and cleaning rollers, where the angle controls flow.
Furniture workshops: small batch bevelled foam parts for chairs, headboards and armrests, cut to drawing without a second machine.
Construction and insulation: angled foam profiles and pipe insulation segments cut on site or in a workshop bay.
How a Bevel Cycle Runs
Set the cutting head to the drawing angle with the scale and the locking handle, then confirm with the angle gauge supplied with the machine.
Set the frequency converter to a feed speed that suits the foam density, slower for dense rebonded foam, faster for soft PU sponge.
Load the block on the feed table and align the reference edge against the guide, so the bevel line follows the block length.
Feed the block through the blade at a steady rate, keeping both hands on the pusher handles and away from the blade line.
Return the block, check the bevel against the sample, and adjust the angle or speed before the batch continues.
Stack the finished parts on a flat pallet, because a bevel cut part keeps its shape only when it is not pressed while cooling.
Selection Guide
Choose the standard angle head when the bulk of your work sits between 45° and 90° and the block height stays under 600 mm.
Choose the roller feed table when your blocks are longer than 2000 mm, as a long block needs support at both ends.
Order the 220 V or 440 V version at the time of the order, as the control circuit and the motor are built to the ordered voltage.
Add a spare blade and a spare guide wheel to the first order, since these are the two parts that wear on a bevel machine.
Installation and Commissioning
Place the machine on a level concrete floor with at least 1200 mm of clear space on the operator side and 800 mm at the blade side, then anchor the four feet. A machine that is not anchored will walk on a loaded bevel pass, and the angle will drift over a shift.
Connect the three phase supply through an isolator rated for the motor and check the blade rotation direction before the first cut. Set the blade tension with the gauge on the carrier, fit the guard, and run an empty cycle at each of the three working angles so the operator learns the changeover before production starts.
Maintenance Calendar
Interval
Action
Daily
Clean foam dust from the blade guide and the table, check the guard and the emergency halt switch.
Every 250 hours
Check blade tension and the guide wheel clearance, retension if the cut line wanders.
Every 500 hours
Inspect the drive belt, grease the pivot of the angle head, check the anchor bolts.
Every 1000 hours
Replace the blade, check the carrier bearings, and recheck the angle scale against a gauge.
Yearly
Inspect the frame welds and the control cabinet terminals, replace the drive belt as a set.
Safe Operation
The blade is guarded on both sides during the pass; the guard is removed only for a blade change and the isolator is locked out first.
The emergency halt switch is within reach of the operator position and tested at the start of every shift.
Feed with the pusher handles only, and keep hands at least 200 mm from the blade line during a loaded pass.
Only one operator runs the machine at a time, and the second person stays clear of the discharge side.
Wear cut resistant gloves and eye protection, since foam dust and blade swarf leave the cutting zone at speed.
Quality Control and Traceability
Each machine is run for 30 minutes at 45°, 60° and 90° before packing, and the bevel of a sample block is checked against a steel square. The motor current is logged at the duty load, the frame is checked for square after assembly, and the serial number is stamped on the frame plate so that a spare part order can be matched to the build. A CE declaration and a test report travel with every set.
Packaging and Delivery
The machine ships nude packed with plastic film and foam sheet, and the blade, angle gauge and small spare parts travel in a wooden case. A 2000 * 1000 * 2000 mm frame fits a 20 ft container with the head lowered. Delivery is about 30 working days after the down payment, and we send the loading photos and the packing list before the container leaves Qingdao.
Frequently Asked Questions
Q: What angle range does this bevel machine cover?
A: The head adjusts continuously from 45 to 90 degrees, with positive detents at 45, 60 and 90 degrees for repeat work.
Q: Which foam materials can it cut?
A: PU sponge, rebonded foam, EVA, PE, EPE, XPE and rubber plastic foam, as well as foam laminated with textile.
Q: What block height can it take?
A: Up to 600 mm cutting height on a 1500 x 2500 mm feed table.
Q: How is the angle set?
A: The head swings on a machined pivot, the operator reads the angle on the scale at the blade line and locks the handle; an angle gauge is supplied for checking.
Q: How long is delivery?
A: About 30 working days after the down payment, with loading photos and the packing list sent before the container leaves Qingdao.
Q: Which voltage is available?
A: 380 V 50 Hz three phase as standard, with 220 V or 440 V built to order at the time of the order.
Talk to Our Engineer
Send us the foam type, the block height and the angle you cut day to day. We will confirm the angle head, the table length and the voltage against your line, and send a quotation with the delivery date for your port.
Company Details
Bronze Gleitlager
,
Bronze Sleeve Bushings
and
Graphite Plugged Bushings
from Quality China Factory
Business Type:
Manufacturer
Year Established:
2002
Total Annual:
1500000-3000000
Employee Number:
50~200
Ecer Certification:
Verified Supplier
XINMEITENG is located in the beautiful seaside city of Qingdao, adjacent to Jinan-Qingdao, Qingyin, Yanqing and Qinghu highways, and connected to Jiaodong International Airport and Qingdao Port Terminal, with a superior geographical location. The company has advanced processing equipment, with more...
XINMEITENG is located in the beautiful seaside city of Qingdao, adjacent to Jinan-Qingdao, Qingyin, Yanqing and Qinghu highways, and connected to Jiaodong International Airport and Qingdao Port Terminal, with a superior geographical location. The company has advanced processing equipment, with more...