China Products/Suppliers. 38*38*25mm Plastic Flooring Fiberglass FRP Grating

Product Specification

When selecting FRP (Fiberglass Reinforced Plastic) Grating, several key parameters determine its suitability for specific applications. Below are the primary parameters to consider:

1. Panel Size and Thickness:

• Panel Size: FRP grating is typically available in standard sizes (e.g., 4x12 ft or 3x10 ft), but custom sizes can be manufactured.
• Thickness: Common thicknesses are 1 inch, 1.5 inches, and 2 inches, which influence the grating's load-bearing capacity and strength.

2. Mesh Size (Opening Size):

• Mesh or Grid Pattern: The open space between bearing bars. Typical patterns include square, rectangular, or custom configurations.
• Open Area Percentage: This refers to the percentage of the panel that is open (non-solid), affecting factors like drainage, ventilation, and the amount of light passing through.
  • Common mesh sizes include 38mm x 38mm (1.5"x1.5") for general use, or smaller mesh (e.g., 19mm x 19mm) for enhanced safety or minimal deflection.

3. Load Capacity (Deflection Limits):

• Load Rating: Grating should be selected based on its ability to carry uniform and concentrated loads. Different grating thicknesses and configurations offer different load-bearing capacities (e.g., 500 lbs per square foot).
• Deflection: Measured in terms of how much the grating flexes under load, typically limited to 1/4" or 1/2" over a span of the grating.

4. Resin Type:

• The resin matrix in FRP grating determines its chemical and environmental resistance. Common resin types include:
  • Isophthalic Polyester Resin: Good general-purpose resin with moderate chemical resistance. Suitable for industrial environments.
  • Vinyl Ester Resin: Offers superior chemical resistance, especially in highly corrosive environments.
  • Orthophthalic Polyester Resin: Standard resin for general use, offering moderate corrosion resistance.
  • Phenolic Resin: Flame-retardant and low-smoke emission, ideal for offshore, marine, and tunnel applications.

5. Fire Rating and Flame Spread:

• FRP grating can be designed to meet fire safety standards. A key parameter is the flame spread rating (typically measured by ASTM E-84 standards). A low flame spread rating (e.g., below 25) is desirable for areas requiring fire retardant materials.

6. Surface Type:

• Gritted Surface: Provides a non-slip surface for enhanced safety, especially in wet or oily conditions.
• Smooth Surface: Easier to clean but offers less traction.
• Concave Surface: Offers some grip without the aggressiveness of gritted surfaces.

7. Span and Deflection Requirements:

• The span between supports determines the required load-bearing capacity. A longer span will require thicker or more robust FRP grating to minimize deflection.
• Deflection limits are typically defined as a percentage of the span length (e.g., deflection ≤ L/100 or L/200, where L is the span).

8. Environmental Factors:

• Corrosion Resistance: The selected resin and design must withstand environmental factors like exposure to chemicals, saltwater, and UV radiation.
• UV Resistance: If the grating is used outdoors, UV stabilizers or protective coatings may be required to prevent degradation over time.

9. Electrical and Thermal Properties:

• Electrical Conductivity: FRP grating is typically non-conductive, making it suitable for applications near electrical equipment.
• Thermal Expansion: FRP has a low thermal expansion coefficient, but it's still important to account for temperature changes in the operating environment.

10. Weight and Density:

• Weight: FRP grating is much lighter than steel or aluminum, with weights ranging between 2 to 5 lbs per square foot depending on thickness and density.
• Density: Affects the overall mass and ease of handling. Lower density gratings are easier to transport and install.

11. Color:

• Standard colors include gray, green, yellow, and beige, though custom colors can be manufactured. Color can also serve functional purposes, such as improving visibility in safety applications.

12. Compliance and Standards:

• ANSI/ASME standards or ASTM D635 testing for flame spread and mechanical properties.
• ASTM E-84: Flame spread classification.
• ASTM D-256: Impact resistance.

By considering these parameters, you can select the appropriate FRP grating for your specific application and environmental needs.