Product Specification

C003 4G Industrail grade GPS tracker For Fleet Management System

4G GPS Tracker MT600 Parameters

1. Specifications

3. Installation

MT600 tracker should be installed by technical professional of local service centre. Without permission, the user cann’t repair and move the tracker randomly. If users do, any unfortunated damage should be compensated by himself.

Installation steps

(caution: the following installation should under no power, otherwise will be dangerous)

1. Power supply line:

The red wire connects 12V“+”;Black wire connects to 12V“-”

2. Wire for cutting off oil of the tracker

Yellow wire connects the relay pin 86; 85 pin connect to 12 V DC , 87 pin and 30 pin in series power supply fuel. Caution: Wrong connection of yellow wire will damage the tracker.

3. Wire for cutting off circuit of the tracker

White wire connects relay pin 86; 85 pin to 12 V DC, 87 pin and 30 pin are in series power supply circuits. Caution: Wrong connection of yellow wire will damage the tracker.

4. Emergency triggering alarm

The blue wire connects the positive of the alarm button, and the black wire connects the negative of the alarm button.

4. Main Functions Commands

When installing the device, please connect supplied wiring loom as follows: (or contact us for help)

• Red: Connect to constant 12V Car Battery(+)
• Black: Connect to Earth (Chassis) Car battery(-)
• Green: Connect to ACC switched 12V Power
• Yellow: Connect to red wire of supplied SOS switch
• White: Connect to Relay terminal (85)
• Pink: Connect to Relay terminal (86)

Note: Relay is optional for remote fuel / ignition shut-off.

1.1 Install the SOS switch (optional)

• Red: connect to Yellow wire from supplied wiring loom
• Black: connect to Earth (Chassis) Car battery(-)

Note: installation Video: http://youtube.com/c/mictrackgps

2. Setup and Configuration

Note: When sending SMS command to the unit, do NOT use spaces or symbols not listed below. [brackets and + are for instructional use only] * and # are valid command parameters.

2.1 Setting Authorized Mobile Phone Numbers

SMS Command format: mobile number+password+[command parameter]

Note: Command Parameter here is the sequence of the mobile number

i.e. [1=Admin] or [2=SOS call number]

For example: *13424392330*0000*1**

Unit Reply: SET USER NUMBER 1 OK.

Note:

• The defaulted password is 0000.
• It can authorize up to 3 phone numbers.

2.2 Deleting authorized number

SMS Command format: password+number+[command parameter]

Note: Command Parameter here is the sequence of the mobile number

i.e. [1=Admin] or [2=SOS call number]

For example: **0000*1**

Unit Reply: DELETE USER NUMBER 1 OK.

2.3 Changing the Admin password

SMS Command format: 777+new password+old password

For example: 77712340000

Unit Reply: SET USER PASSWORD OK.

2.4 Instant Location Request (used to receive unit location via SMS)

SMS Command format: 666+password

For example: 6660000

When sent, this command will result in a Unit Reply SMS as follows:

ID:865662000409210

Date:05:36:59 11/11/2016

Fix:A State:SMS

http://maps.google.com/maps?q=+22.63146%2c1+14.03701

Note: This link can to be opened on any Smart Phone to reveal the Google Maps Location of the unit at the time of request

2.5 SOS Alarm (optional)

When the SOS button is pressed for 3 seconds, the unit will automatically send it’s location to authorized phone number via SMS, and also upload location data to the Web Tracking Platform server along with the status description “SOS”

2.6 Round Geo-fence (Setting of size and shape of Geo-Fence)

SMS Command format: 005+password+R+[Command Parameter]

Note: Command Parameter here is fence diameter in KM [0.1~999.9]

For example: 0050000R1.0

Unit Reply: SET ROUND GEO-FENCE:ON

2.6.1 Enable the Round Geo-fence

SMS Command format: 211+password

For example: 2110000

Unit Reply: SET ROUND GEO-FENCE: ON.

2.6.2 Disable the Round Geo-fence

SMS Command format: 210+password

For example: 2100000

Unit Reply: SET ROUND GEO-FENCE: OFF.

2.7 Square Geo-fence (Setting of dimensions and shape of Geo-Fence)

SMS Command format: 006+password+G1,IO/I/O,E/W longitude upper limit+N/S latitude upper limit,E/W longitude lower limit+N/S latitude lower limit.

For example: 0060000G1,IO,E114.04540N22.59034,E114.05978N22.59797

Unit Reply: SET SQUARE GEO-FENCE1(IO)OK.

2.7.1 Enable the Square Geo-fence

SMS Command format: 311+password

For example: 3110000

Unit Reply: SET SQUARE GEO-FENCE: ON.

2.7.2 Disable the Square Geo-fence

SMS Command format: 310+password

For example: 3100000

Unit Reply: SET SQUARE GEO-FENCE: OFF.

2.8 Remote cut off fuel and ignition (optional)

To remotely Cut-Off fuel or power

SMS Command format: 940+password

For example: 9400000

Unit Reply: SET OILWAY DISCONNECT.

To remotely Resume fuel or power

SMS Command format: 941+password

For example: 9410000

Unit Reply: SET OILWAY RECOVERY CONNECT.

Note: The default setting for the Cut-Off feature is OFF

2.9 External power cut off alarm

If the external power to the unit is disconnected, [i.e. unit tampering or vehicle battery removal] the unit will call the authorized phone numbers, and then send location data to the authorized phone number and upload location data to the Web Tracking Platform server along with the status description “DEF”

2.10 Towing alarm

If the vehicle was be moved or towed when ACC is turned OFF, it will SMS location data to the authorized phone number, and upload location data to the Web Tracking Platform server along with the status description “TOWED”

2.11 Low battery Alarm (internal backup battery)

When the unit’s internal backup battery is low, it will SMS the authorized phone number, and upload location data to the Web Tracking Platform server along with the status description “BLP”

2.12 Low battery Alarm (Vehicle Battery)

When the vehicle battery is low, it will SMS the authorized phone number, and upload location data to the Web Tracking Platform server along with the status description “CLP”

2.13 High Temperature Alarm

When the devices internal temperature is high [preset value] it will SMS the authorized phone number, and upload location data to the Web Tracking Platform server along with the status description “HT”

2.14 Over-Speed alarm (Alerts that the unit is exceeding a preset speed)

SMS Command format: #122#user password#[Command Parameter]##

Note: Command Parameter here is [Km/Hour]

Example: #122#0000#100##

Unit Reply: SET SPEED LIMIT:ON

To disable the Over-Speed Alarm

SMS Command format: #122#0000#0##

Note: Command Parameter here is [0=OFF]

Unit Reply: SET SPEED LIMIT:OFF.

Note: Speed is in KM/H, Maximum setting = [999].

1 SIM Card installation

• Insert the SIM card into the SIM card plastic tray.
• Ensure the SIM card has metal contacts facing up (Diagram #1).
• Gently slide the SIM Tray into the SIM Slot (Diagram #2).

1. Application

• 4G LTE network support (fallback to 3G/2G network)
• Real-time tracking
• Vehicle trip history and mileage data on web server
• SOS alarm reporting (optional)
• ACC switch status report
• Geo-Fence alarm and reporting
• External power cut off alarm
• Remote cut off fuel / ignition (optional)
• Vehicle towing / Movement alarm
• Over-Speed alarm and reporting
• Backup battery low power alarm
• Car battery low power alarm
• High temperature alarm
• Power saving / sleep mode