NT150L Kelvion Platten Customized GEA Gasket And Plates

Product Specification

NT150L H/V GEA-Kelvion Platten Customized Plate Heat Exchanger

Plate Heat Exchanger Introduction

NT150L  Model Plate Heat Exchanger Specification
 

NT150L  Plate Heat Exchanger Technical Information

NT150L Plate Heat Exchanger Gasket & Plate Pictures

NT150L Plate Heat Exchangers Application And Benefits

Application:

With M&C Heat Parts product group, the NT series is a gasketed plate heat exchanger for multiple applications. Variety of materials that work across a broad range of liquids, temperatures and pressures. Well-suited for these liquid-to-liquid applications:

Benefits:

Versatility-

• The right design, not a "good enough" design. A wide variety of materials, sizes, and plate configurations combine with sophisticated selection software to ensure a perfect selection, whatever your needs.
• The compact footprint allows you to use it in locations that you wouldn't dream of with a shell and tube heat exchanger.

Higher Performance at a Lower Cost -

• Optiwave plate corrugations distribute the liquid evenly across the entire plate width, maximizing heat transfer and minimizing the number of plates (and cost) required.

Convenient Maintenance-

• PosLoc plate lead-ins cause the plate pack to self-align when re-installing.
• Ecoloc tools-free gaskets make gasket replacement a snap.
• Individual plates mean no heavy lifting tools are needed. Faster more efficient maintenance, with shorter down times.

Long Service Life-

• Careful corrugation design provides the ideal balance of high turbulence and proper fluid distribution, reducing fouling from less than perfect media.

Noted Plate Heat Exchanger Hazards

• The PHE is heavy. If it falls over or falls down during transport, persons may be killed or seriously injured. Transport the PHE to its intended posi- tion with the transport packaging if possible. Use sufficiently dimen- sioned lifting equipment exclusively for handling the PHE at the place of installation. Never stand underneath suspended loads and keep other persons away.
• Upright PHEs have a high center of gravity and may easily tip over. Put up a PHE delivered in a horizontal position only directly before it is installed. Secure the upright PHE against tipping over by bolting it to the ground. If possible, remove the lifting devices used only after the PHE has been fastened to the ground.
• The use of dangerous flow media (explosive, flammable, caustic, toxic) involves danger of chemical burns, fire burns or intoxication. Wear suit- able protective clothing when working on the PHE. Ensure that the PHE is depressurized and empty prior to opening.
• When opening the PHE, sharp-edged HE plates may fall out. Keep HE plates from falling out by having them secured by another person.When processing cold or hot flow media, the surfaces of the PHE may be colder than 0 °C or hotter than 50 °C. This is why PHEs involve the danger of frostbites and burns. Protect persons by a protection against accidental contact and install warning signs relating to frostbites and burns.
• A cutting hazard exists on burrs, threads and the HE plates. Wear protective equipment at all times when working on the PHE.

Plate Heat Exchanger Intended Use

The PHE is a component intended for permanent installation in a plant or a machine. It serves for heat transmission from the heat-releasing flow medium to a heat-accepting flow medium.

We recommend that you put the PHE into operation only after checking if the plant or machine into which the PHE has been integrated meets the appli- cable national regulations, safety rules and standards.

The PHE is a technical equipment and not intended for private use. It is basi- cally designed for mostly stationary use.

The PHE was designed and built specifically for the operating conditions you have specified. The operating conditions are documented in the technical documentation:

• Min./max. allowed pressure
• Min./max. allowed temperature
• Flow rates
• Type and composition of flow media
• Additional loads if allowed
• Deviating from these allowable operating conditions will void the warranty and the operating permit. The same applies to unauthorized essential modifications on the PHE.
• Please contact your Kelvion Sales Office for verifying such requirements and the possibly required modifications.

The intended use also includes:

• Compliance with the present operating instructions and the technical documentation included in the delivery;
• That the plate heat exchanger is in technically flawless condition, i.e. it shows no apparent defects, e.g. loose or missing tensioning bolts, leaks due to defective HE plates and/or frame gaskets.
• Observing the national and international laws, decrees, regulations, guidelines and other rules, e.g. occupational safety and accident preven- tion regulations, applicable at the place of installation even if these are not listed in the present operating instructions.

Plate Heat Exchanger Pictures

M&C Heat Parts Company Profile

M&C Heat Parts Co., Ltd is founded in Wuxi, Jiangsu. M&C is specialized in designing and manufacturing high quality heat transfer equipment. The range of products comprises plates & gaskets, plate heat exchangers, gasketed heat exchangers and brazed heat exchangers. Thus, as one of the few producers worldwide, M&C offers solutions with optimum thermodynamic designs for different industries and virtually all applications.

M&C provide you with one-stop accessories service, multuple-brand & multiple model alternatives for your choice. We'll meet all your requirements of plate heat exchanger and keep your machine running contunously through our rich storage and quick response.

Moreover, we have a strict quality control and after-sales service system, from material purchasing to finished product package until the product received in good condition. Our products have been widely used all over the world in various fields.

M&C Plate Heat Exchanger Plates & Gaskets Other Models Recommend

Sondex/Danfoss - S4A, S7, S20, S21, S22, S41, S43, S47, S65, S81, S86, S100, S120, S130, SFD7, SFD13, SW19 and so on;

APV/SPX - H17, N25, N35, A055, A085, J060, J092, J107, M92, M107, K55, K71, B110, B134, P105, P190, SR1, SR2, TR9GN, TR9AL and so on;

Tranter/Swep - GX12, GL13, GC26, GC51, GX26, GX51, GX42, GX64, GX85, GX91, GX140, GX145 and so on;

API/Schmidt - Sigma 7, Sigma 9, Sigma 13, Sigma 26, Sigma 27, Sigma 36, Sigma 66, Sigma 106, Sigma 229, Sigma Star 45, Sigma Star 90 and so on;

Vicarb - V4, V13, V20, V28, V45, V60, V100, V110, V130 and so on;

Hisaka - EX11, EX15, EX15, LX026, LX195, LX395, LX595, RX135, RX395, RX595, UX115, UX225, UX395, UX495, UX815, UX995 and so on;

GEA - VT04, VT10, VT20, VT40, VT80, VT405, VT805, VT1306, NT50M, NT50X, NT100S, NT150S, NT150L, NT250M, NT250L and so on;

Funke - FP04, FP05, FP14, FP16, FP08, FP22, FP31, FP40, FP41, FP70, FP100, FP120 and so on;

Thermowave - TL200SS/PP, TL250SS/PP, TL400SS/PP. TL650SS/PP and so on;

DHP - DX143, DX146, DX20V, DX20DL, DX20DM, DX30S, DX36M and so on;

LHE - HT101, HT102, HT104, HT151, HT152, HT202, HT232, HT233 and so on;

M&C Plate Heat Exchanger Goods ready to Delivery