Product Specification

YD44-003 9 Gallon Square Mobile Oil Drainer with Tool Tray (9 Gallon Square Mobile Oil Drainer with Tool Tray YD44-003) Webpage Detail Page (English)

I. Product Specifications (SPECIFICATION)

1. Core Parameter Summary Table

2. Performance Test Table

II. Product Details (PRODUCT DETAILS)

1. Square Tank + 9-Gallon Capacity, Dual Improvement of Space and Efficiency

(1) Square Design, Suitable for Narrow Scenarios

• Fitting Storage: The square tank can be placed close to corners, equipment gaps, or the edge of maintenance workstations, saving 30% space compared to round oil drainers. It is especially suitable for small-area scenarios such as community repair shops and home garages; for example, it can be placed in a 40×40cm corner of a home garage without occupying vehicle parking space;
• Convenient Batch Placement: When repair shops purchase in bulk, square equipment can be closely stacked, and the loading capacity of a 40-foot container is 20% more than that of round products, reducing logistics costs by 15%.

(2) 9-Gallon Large Capacity, Reducing Dumping Frequency

• 35L Oil Storage Space: 5L more than 8-gallon products of the same type, capable of collecting oil change volume of 2 light trucks (approx. 15L each) or 3 family cars (approx. 4-5L each) at a time. No frequent dumping is required during batch oil changes in repair shops, increasing efficiency by 40%;
• High Liquid Level Warning: Maximum capacity scale lines are marked on the side of the tank to prevent waste oil overflow, ensuring safe operation even for beginners.

2. Spring Clip Quick Adjustment + Tool Tray Storage, Zero Operation Threshold

(1) Tool-Free Height Adjustment, Suitable for All Equipment

• One-Click Unlock with Spring Clip: Press the clip to pull the pipe, no need to remove bolts. Operation can be completed while standing without bending, reducing the average adjustment time of maintenance personnel from 1 minute to 5 seconds;
• Precise Positioning: The pipe positioning grooves closely match the spring clip. Even in a vibrating environment (e.g., tractor idling during oil change), the funnel will not deviate from the oil drain port, achieving a 100% waste oil collection rate.

(2) Dual-Function Tool Tray, Avoiding Scattering

• Accessible Tools: During oil change, tools (wrenches, gaskets, new filters) are classified and placed in the tool tray, accessible with a reach. This solves the problem of "tools scattering on the ground and being hard to find" and shortens maintenance time by 20%;
• Non-Slip Handle: The tool tray handle adopts a non-slip texture design, providing a comfortable grip when pushing the equipment. No need to touch the oil-stained tank, keeping hands clean.

3. HDPE Corrosion Resistance + 4-Wheel Mobility, Balancing Durability and Convenience

(1) Durability in Extreme Environments

• Full HDPE Material: The oil tank and funnel are resistant to corrosion from various vehicle waste oils, with no swelling or cracking during long-term use. The service life is 3 times longer than that of ordinary PP plastic oil drainers;
• High/Low Temperature Adaptability: No brittleness during outdoor operations in northern winter (-30℃), no deformation when pouring 80℃ high-temperature waste oil. No need to worry about seasonal or environmental restrictions.

(2) Flexible Mobility and Stable Locking

• Smooth Swivel Casters: 2.5-inch wheel diameter adapts to various ground surfaces (concrete, asphalt, workshop floor tiles), with pushing resistance ≤30N. A single person can easily push the equipment fully loaded with 35L of waste oil;
• Brake Anti-Sliding: Press the caster brake during oil change operations to keep the equipment stable without displacement. Even on a 5° inclined ground, the funnel can be accurately aligned with no spillage risk.

III. Application Scenarios (APPLICATION SCENARIOS)

1. Oil Change for Light Trucks in Narrow Workstations of Community Repair Shops (Core Scenario)

1. Equipment Preparation and Space Adaptation:
   - The maintenance personnel holds the tool tray handle, pushes YD44-003 to the corner of the workstation (40×40cm space). The square tank fits the corner without occupying the passage; presses the spring clip to adjust the height to 55 inches (139.7cm), aligns it with the light truck's oil drain port, and presses the brake to lock;
   - Places a 19mm wrench, oil drain plug gasket, and new oil filter in the tool tray;
   2. Waste Oil Collection and Oil Change Operation:
   - Removes the oil drain plug; waste oil flows into the oil drainer, and 15L of waste oil is collected in 13 minutes (no mid-process dumping required due to 9-gallon capacity);
   - During collection, takes the wrench from the tool tray to replace the oil filter, no need to go back and forth to the tool cabinet, avoiding tool scattering;
   - After oil change, releases the brake and pushes the equipment to the waste oil barrel. The 35L large capacity can hold waste oil from the next oil change, no immediate dumping required;
   3. Operation Effect:
   - Space Adaptation: The square design fits the corner without affecting the maintenance passage, increasing workstation utilization by 30%;
   - High Efficiency: Large capacity reduces dumping frequency, tools are accessible, and oil change is completed within 1 hour, saving 25 minutes compared to traditional equipment;
   - Convenience: 6.3kg lightweight design allows one person to move it, with no physical pressure during operation.
   Result: The oil change efficiency of the narrow workstation in the community repair shop is improved, customer waiting time is shortened, and the workstation can serve more vehicles at the same time.

2. Oil Change for Tractors in Agricultural Machinery Maintenance Stations (Scenario 2)

1. Equipment Adjustment and Tool Preparation:
   - Pushes YD44-003 to the tractor, presses the spring clip to adjust the height to 68 inches (172.7cm), aligns it with the hydraulic oil drain port, and locks the casters;
   - Places a hydraulic oil-specific wrench, new filter, and rag in the tool tray;
   2. Waste Oil Collection and Maintenance:
   - Opens the oil drain valve; waste oil flows into the 35L tank through the funnel, and 20L of waste oil is collected in 17 minutes. The remaining space can hold waste oil from the next oil change;
   - During collection, takes the wrench from the tool tray to remove the old filter and replace it with a new one, no need to carry tools separately;
   - After maintenance, pushes the equipment to the waste oil recycling area. The square tank is stored against the corner of the recycling area without occupying maintenance space;
   3. Maintenance Effect:
   - Precise Height: 68 inches fully aligns with the high-chassis tractor, no waste oil spillage;
   - Sufficient Capacity: 20L of waste oil is collected at one time, no mid-process dumping required, increasing maintenance efficiency by 50%;
   - Standardized Tools: Tool tray storage avoids loss, making the maintenance process smoother.

3. DIY Car Oil Change in Home Garages (Scenario 3)

1. Equipment Storage and Startup:
   - Takes YD44-003 from the corner of the garage (the square design fits the corner, occupying only 0.04㎡ for storage), presses the spring clip to adjust the height to 28 inches (71.1cm), aligns it with the car's oil drain port, and locks the casters;
   - Places a 17mm wrench, oil drain plug, and new oil filter in the tool tray;
   2. DIY Oil Change Operation:
   - Uses the wrench from the tool tray to remove the oil drain plug, and collects 4.5L of waste oil in 5 minutes;
   - When replacing the new oil filter, takes the accessory from the tool tray without worrying about tools falling;
   - After oil change, holds the tool tray handle to push the equipment back to the corner for storage. The 35L capacity can temporarily store waste oil, which can be transferred to a recycling station after 2-3 accumulations;
   3. DIY Effect:
   - Space-Friendly: The square design does not occupy the main area of the garage, allowing normal vehicle parking;
   - Easy Operation: Tool-free height adjustment enables beginners to complete the oil change within 1 hour, saving 100 yuan compared to going to a repair shop;
   - Convenient Storage: Tools and equipment are stored together, no need to find tools again for the next use.

IV. Frequently Asked Questions (FAQ)

Q1: When dumping waste oil from the square tank, will residual oil be left in the corners, making it impossible to dump completely?

1. Inclined Diversion Design: The tank bottom is inclined 3° toward the drain port, allowing waste oil to naturally converge to the drain port. The residual amount is ≤50ml (much lower than 100ml of round tanks);
2. Dumping Technique: Tilt the equipment 15° toward the drain port when dumping, and gently shake the tank at the same time to allow residual waste oil to flow out completely;
3. Deep Cleaning: If there is viscous residue (e.g., gear oil), add a small amount of diesel (approx. 50ml) to the tank, shake it and dump. Diesel can dissolve residual oil stains, then wipe the tank bottom with a rag.

Q2: When adjusting the height, the spring clip gets stuck and the pipe cannot be pulled smoothly. What is the reason?

1. Clean the Spring Clip: Wipe the inner side of the spring clip with a rag dipped in alcohol to remove oil and impurities, ensuring smooth movement of the clip;
2. Clear the Positioning Grooves: Gently unclog impurities (e.g., iron filings, fibers) in the pipe positioning grooves with a thin iron wire, then apply a small amount of lubricating oil (e.g., sewing machine oil). The pipe can be pulled smoothly after that;
3. Avoid Forced Pulling: Do not pull hard if it is severely stuck to prevent pipe deformation. If it is still stuck after cleaning, contact the merchant to replace the spring clip.

Q3: After placing tools in the tool tray, tools easily collide and make noise when moving the equipment. How to handle this?

1. Partitioned Storage: Place small partition boxes (e.g., plastic grid boxes) in the tool tray to classify and store wrenches, bolts, gaskets, etc., avoiding mutual collision;
2. Stick Anti-Slip Pads: Stick silicone anti-slip pads (matching pads provided by the merchant) on the bottom and inner wall of the tool tray to increase friction between tools and the tray, reducing shaking and collision;
3. Control Tool Quantity: The maximum load capacity of the tool tray is 2kg. Do not overload it to avoid stacking and collision caused by excessive tools.

Q4: Can additional accessories (e.g., liquid level sensors) be installed on the square tank?

1. Risks of Self-Installation: The HDPE tank material is relatively brittle. Drilling holes for self-installation of accessories may cause cracking and leakage, and may damage the original sealing structure, leading to waste oil leakage;
2. Official Matching Solution: If liquid level warning function is needed, contact the merchant to purchase a dedicated liquid level sensor (matching model with pre-reserved installation holes) and have it installed by professionals to ensure equipment sealing and safety;
3. Alternative Solution: Clear capacity scale lines are marked on the side of the tank, allowing liquid level observation with the naked eye. No additional accessories are needed, and operation is simpler.