| Sealing | IP54 |
| Material | Sealed geared strut, steel bracket, ABS module |
| Set Weight | 5.0 kg |
| Peak Current | 8A per set |
| Delivery Time | 8-18 working days bulk, stock dispatch within 5 days |
| Full Travel | 7-8 seconds |
| Sleep Current | Below 0.1A |
| Cycle Test | 50000 operations |
| Temperature Range | -30°C to +70°C |
| Payment Terms | T/T,L/C,Western Union,PayPal |
| Actuators | Two geared struts, sealed |
| Supply Ability | 800 Sets per Month |
| Packaging Details | One set carton 79x21x19 cm, two sets 82x25x36 cm, foam lined with moisture barrier bag |
| Voltage | 12V DC |
| Brand Name | Liush |
| Model Number | For DFSK Glory 580 / Fengon 580 2016-2018 |
| Place of Origin | Guangdong, China |
| Certification | ISO 9001:2015 |
View Detail Information
Explore similar products
Electric Trunk Back Door Remote Control Power Liftgate Kit For Dongfeng Nammi 06
Automatic Electric Sliding Door Kit Remote Power Side Door For Dongfeng Yumsun
Door Remote Control Power Tailgate Retrofit Kit For Dongfeng Nammi 01
Electric Trunk Lift Kit Smart Tailgate Kit OEM Supported for Dongfeng Fengshen
Product Specification
| Sealing | IP54 | Material | Sealed geared strut, steel bracket, ABS module |
| Set Weight | 5.0 kg | Peak Current | 8A per set |
| Delivery Time | 8-18 working days bulk, stock dispatch within 5 days | Full Travel | 7-8 seconds |
| Sleep Current | Below 0.1A | Cycle Test | 50000 operations |
| Temperature Range | -30°C to +70°C | Payment Terms | T/T,L/C,Western Union,PayPal |
| Actuators | Two geared struts, sealed | Supply Ability | 800 Sets per Month |
| Packaging Details | One set carton 79x21x19 cm, two sets 82x25x36 cm, foam lined with moisture barrier bag | Voltage | 12V DC |
| Brand Name | Liush | Model Number | For DFSK Glory 580 / Fengon 580 2016-2018 |
| Place of Origin | Guangdong, China | Certification | ISO 9001:2015 |
| High Light | Electric Car Trunk Retrofit ,Automatic Trunk Opener OEM ,Auto Tailgate Lift Kit | ||
Early production 580s are now seven to nine years old, and the gas springs have usually lost part of their charge. Owners either live with a hatch that drops or replace the springs and face the same problem again in a few seasons. This retrofit solves the cause rather than the symptom: two motorised struts take over the lifting work, a controller reads the factory latch, and the hatch opens and closes by button instead of by hand. Wiring plugs into the existing body connector, brackets bolt to the original studs, and nothing on the car is modified permanently.
Cars built between 2016 and 2018 use a different upper hinge and stud height from the later facelift and Pro versions. This kit carries the early bracket pair and an actuator matched to that shorter stroke, so the panel stops exactly where the factory geometry intends. Buyers should check the build plate before ordering; if the body turns out to be a later variant we exchange the bracket set before shipment at no cost.
| Vehicle | Production | Bracket pair |
|---|---|---|
| Glory 580 / Fengon 580 | 2016-2018 | Early type, this listing |
| Glory 580 / Fengon 580 facelift | 2018 onwards | Facelift type, separate listing |
| Glory 580 Pro / Fengon 580 Pro | Pro body | Pro type, separate listing |
Four triggers are supported: factory remote, cabin button, rear handle switch and foot sensor. The module checks gear position first, then releases the latch and ramps the struts up smoothly. Current is monitored continuously, so any obstruction stops and reverses the panel at once. Two open heights can be stored, the close is cushioned to spare the latch, and manual operation stays available if power is lost. After 30 seconds idle the system sleeps and draws under 0.1A.
| Item | Value |
|---|---|
| Fitment | DFSK Glory 580 / Fengon 580, 2016-2018 |
| Voltage | 12V DC |
| Actuators | Two geared struts, sealed |
| Full travel | 7 to 8 seconds |
| Peak current | 8A per set |
| Sleep current | Below 0.1A |
| Sealing | IP54 |
| Temperature range | -30 C to +70 C |
| Cycle test | 50,000 operations |
| Set weight | 5.0 kg |
| Warranty | 24 months |
Allow about 90 minutes in a workshop bay: isolate the battery, unbolt the old springs, fit the early brackets, clip in the actuators, route the harness along the factory path, mount the module and sensor, then refit the trim and run the learning routine twice. No cutting, welding or painting is required at any point. Our technical desk reviews photos or short video from the installer and answers in English within one working day.
One set per foam-lined carton at 79 x 21 x 19 cm, two sets at 82 x 25 x 36 cm, both with a moisture barrier bag and step-numbered fastener packs. Bulk lead time 8 to 18 working days, stock dispatch inside 5 days when available. Air, sea and express shipping quoted on request. OEM carton and manual printing from 200 sets. Actuators, modules, harnesses, brackets and switches available as separate service parts.
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler
Year Established:
2020
Total Annual:
120,000,000-USD 150,000,000
Employee Number:
400~500
Ecer Certification:
Verified Supplier
Your Trusted Partner in Automotive Intelligent Upgrade Accessories ⚙️ Independent R&D ???? Standardized Production ???? Global Sales ????️ One-Stop After-Sales Who We Are Shenzhen Liush Auto Parts Co., Ltd. is a subsidiary of Liush Group, founded in 2020. We own independent export rig... Your Trusted Partner in Automotive Intelligent Upgrade Accessories ⚙️ Independent R&D ???? Standardized Production ???? Global Sales ????️ One-Stop After-Sales Who We Are Shenzhen Liush Auto Parts Co., Ltd. is a subsidiary of Liush Group, founded in 2020. We own independent export rig...
Get in touch with us
Leave a Message, we will call you back quickly!