ISOLine NORGREN Cylinder RA 802080 M 160 Tie-Rod Double Acting New Original

Product Specification

NORGREN RA 802080 M 160 ISOLine Tie-rod Double Acting Cylinder High Safety New Original

Product Description:

Advantages and features of Norgren tie rod double-acting cylinder

‌Standardized design and high compatibility‌

Complies with international standards such as ISO 15552 and ISO 6431, the built-in tie rod structure enhances the rigidity of the cylinder body, supports interchangeability with other brands of cylinders, and facilitates system integration and maintenance;

Modular components support quick disassembly and assembly, combined with Easy-2-Combine technology to achieve multi-cylinder combination, adapting to the needs of complex automated production lines.

‌Efficient output and bidirectional power‌

The double-acting design alternately supplies air on both sides of the piston to achieve bidirectional output thrust (maximum pressure 12 bar), which is suitable for frequent reciprocating motion scenarios (such as stamping, material handling);

The thrust range covers 50~2000 N, supports precise adjustment of stroke (minimum 10 mm), and the repeatability accuracy reaches ±0.1 mm.

‌Long life and low maintenance‌

Using polyurethane seals and propylene resin dust rings, the friction coefficient is low and the wear resistance is strong, with a service life of more than 5 million cycles;

Built-in elastic buffer device can absorb the impact energy of high-speed piston movement (0.1~1.5 m/s) and reduce vibration and noise.

‌Environmental adaptability‌

With a temperature range of -25℃~80℃ and a protection level of IP65, it can cope with harsh industrial environments such as dust and moisture;
The oil content of the gas source is low (0~5 mg/m³), and it is suitable for ordinary compressed air systems.

Precautions for use

‌Installation specifications‌

It is necessary to ensure that the cylinder axis is consistent with the direction of load movement to avoid lateral force causing piston rod bending or seal wear; the mounting bracket must be firmly fixed to prevent vibration deviation;

Clean the gas pipeline thoroughly before installation. It is recommended to use a 50 μm precision filter to prevent particulate impurities from entering the cylinder body.

‌Air source and working condition adaptation‌

It is recommended that the compressed air pressure be stable at 6~8 bar. A pressure reducing valve should be configured for overpressure use; high temperature resistant seals should be selected for high temperature environment (＞50℃);

Double-acting cylinders should be equipped with three-position five-way solenoid valves to ensure stable two-way air supply and avoid motion jamming caused by air supply delay.

‌Operation and maintenance‌

Lubrication management: Use Norgren special grease (such as ISO VG32) and apply it to the piston rod surface once a week. If it is not used for a long time, the air path needs to be exhausted and anti-rust oil needs to be applied;

Regularly check the sealing: After pressurizing to the rated value, use soapy water to detect interface leakage. If the leakage exceeds 0.5 L/min, the sealing ring needs to be replaced.

‌Safety and fault prevention‌

Buffer adjustment: Adjust the buffer strength through the throttle valve (such as RTSC series) to prevent the piston from hitting the end cover;

after adjustment, it is necessary to test the no-load operation for 5~10 times to verify the effect;

Overload protection: The opening and closing torque does not exceed 240 N·m. The kinetic energy output needs to be limited (≤1.5 J) in the impact scene to prevent the pull rod from deformation or thread damage.

Through reasonable selection and standardized operation, Norgren tie rod double-acting cylinders can be widely used in automobile assembly, packaging machinery, punching equipment and other fields, taking into account high-precision control and long-term reliability.

FAQ

Q1: Wonder if you accept small orders?
A1: Do not worry. Feel free to contact us .in order to get more orders and give our clients more convener ,we accept small order.

Q2: Can you send products to my country?
A2: Sure, we can. If you do not have your own ship forwarder, we can help you.

Q3: What's your payment terms ?
A3: By T/T,LC AT SIGHT,100% full payment.

Q4: How long is your production lead time?
A4:It depends on product and order qty. Normally, it takes us 15 days for an order with MOQ qty.

Q5: When can I get the quotation ?
A5: We usually quote you within 24 hours after we get your inquiry. If you are very urgent to get the quotation.Please call us or tell us in your mail, so that we could regard your inquiry priority.