Siemens 6ES7288-2DR32-0AA0 S7-200 SMART, Digitale E/A SM DT16, 8DI/8DO, 8 DI DC

Product Specification

Siemens 6ES7288-2DR32-0AA0

SIMATIC S7-200 SMART, Digitale E/A SM DT16, 8DI/8DO, 8 DI DC 24V, Sink/Source, 8 DO, Transistor 0.75A
Input Current
From the backplane bus DC 5 V, typ. 115 mA; 5 V DC from the CPU module
The output voltage
Measuring the supply voltage of the inverter
● Rated value (DC) 24 V
● short-circuit proof No
digital input
Number of digital inputs 8
● in components 2
Parallel switch at the input Yes
Input characteristics according to IEC 61131, type 1 yes
Number of simultaneous controllable inputs
Horizontal installation position
— up to 50 °C, max 8
vertical installation position
— up to 40 °C, max 8
Input voltage
● Input voltage type DC
● Rated value (DC) 24 V
● For signal "0" < 5 V DC
● For signal "1" +15 to +30V
Input Current
● For signal "0", maximum value (permissible closed-circuit current) 1 mA
● For signal "1", the minimum value is 2.5 mA
● For signal "1", the maximum value is 5 mA
● For signal "1", typ. 4 mA
For unclosed contacts
— for signal "0", maximum (permissible closed-circuit current) 10 µA
Input delay (when input voltage is rated value)
for standard input
— When going from "0" to "1", the maximum value is 200 µs
— when going from "1" to "0", the maximum value is 200 µs
wire length
● Shielded, max. 500 m
● Unshielded, max 300 m
digital output
Number of digital outputs 8
● in components 2
M switch no
P switch yes
Short circuit protection no
On-off capability of the output
● Maximum value 0.75 A with resistive load
● Maximum 5 W at lighting load
The output voltage
● Rated value (DC) 24 V
● for a maximum value of 0.1 V for signal "0"
● For signal "1", min. 20 V
● For signal "1", the maximum value is 28.8 V; the maximum value is related to the input source L+ *
Output current
● Rated value for signal "1" 0.75 A
Output delay with resistive load
● From "0" to "1", maximum 50 µs
● From "1" to "0", maximum 200 µs
The two outputs are connected in parallel
● for logical connection yes; only outputs of the same group
● For increasing power yes; possible (only outputs in the same group)
● For redundant control loads Yes; only outputs in the same group
Total current at the outputs (per group)
All installation locations
— up to 40 °C, max. 3 A
Horizontal installation position
— up to 50 °C, max. 3 A
vertical installation position
— up to 40 °C, max. 3 A
All other installation locations
— up to 40 °C, max. 3 A
Alarm/Diagnostic/Status Information
Diagnostic Display LEDs
● for input status yes
● for output status yes
Galvanic isolation
Galvanic isolation of digital inputs
● between channels yes; optocoupler
Potential isolation of digital outputs
● between channels yes; optocoupler
insulation
Insulation test with 500V AC for 1 minute
EMV
Ability to resist static discharge interference
● Immunity to static discharge per IEC 61000-4-2 Yes; ±4 kV contact discharge (according to IEC 801-2/IEC 1000-4-2; ESD); ±8 kV air discharge (according to IEC 801-2/ IEC 1000-4-2; ESD)
— Test voltage during air discharge 8 kV
— Test voltage at contact discharge 4 kV
Anti-interference ability against high frequency electromagnetic fields
● Immunity to high frequency radiation according to IEC 61000-4-3 yes
— High frequency radiation in the frequency range 80 to 1000 MHz, 10 V/m, 1.4 to 2.0 GHz, 3 V/m, 2.0 to 2.7 GHz, 1 V/m (87 MHz to 187 MHz, 174 MHz to 230 MHz and 470 MHz In the range of MHz to 790 MHz: 3V/m)
Wire-related immunity to interference
● Interference immunity of mains conductors according to IEC 61000-4-4 Yes; 2 kV according to IEC 61000-4-4, impulse
● Interference immunity of signal conductors according to IEC 61000-4-4 Yes; ±2 kV according to IEC 61000-4-4, impulse
Anti-interference ability of pin shock voltage (surge)
● Mains lead according to IEC 61000-4-5 Yes; with pre-protective element
● Asymmetric coupling
— Test voltage 2 kV on supply conductors
- Test voltage 2 kV on signal conductors (greater than 30 m)
Interference immunity against the amount of wire interference caused by high-frequency fields
● Interference immunity for high-frequency feeds according to IEC 61000-4-6 yes
● Immunity to high-frequency radiation according to IEC 61000-4-6 Yes; 10 V/m with 80 % amplitude modulation 1 kHz
— Test voltage 10 V at 80% 1KHz amplitude modulation in the range 9 kHz ... 80 MHz
Suppression of radio interference emissions according to EN 55 011
● Radio radiated interference Emitted interference according to EN 50081-2, tested according to EN 55011, class A, group 1
● Limit value class A for applications in the industrial sector yes
Protection class and protection category
Degree of protection according to EN 60529
● IP20 yes
size
width 45 mm
Height 100mm
Depth 81 mm
weight
Weight, about 179.7 g