Ningbo Anyo Import & Export Co., Ltd.
| Supply Ability | 50000pcs per day |
| Packaging Details | 10000pcs/carton, 9kg, 23.5*24*27cm |
| Delivery Time | 8-10 work days |
| Payment Terms | L/C, T/T |
| Other name | Electret microphone |
| Impedance | Low impedance(2.2KΩ-30%) |
| Sensitivity | -30dB~44dB |
| Current consumption | Max. 0.5mA |
| Operation voltage | 4.5V |
| Resistance | 2.2KΩ |
| Brand Name | ANYO |
| Model Number | DGO9767CD |
| Place of Origin | CHINA |
View Detail Information
Explore similar products
2 Terminals Electret Condenser Microphone -40±3dB Size 9.7*6.7 mm For Telephones
Black Passive Electronic Components Waterproof Tact Switch 6x6 With Copper Pin
DIP SPST Momentary Tact Switch 12x12 / Square Actuator For Medical Device
2.54mm Pitch Slide DIP Switch , 1～12 Position DIP Switch With Dual In Line
Product Specification
| Supply Ability | 50000pcs per day | Packaging Details | 10000pcs/carton, 9kg, 23.5*24*27cm |
| Delivery Time | 8-10 work days | Payment Terms | L/C, T/T |
| Other name | Electret microphone | Impedance | Low impedance(2.2KΩ-30%) |
| Sensitivity | -30dB~44dB | Current consumption | Max. 0.5mA |
| Operation voltage | 4.5V | Resistance | 2.2KΩ |
| Brand Name | ANYO | Model Number | DGO9767CD |
| Place of Origin | CHINA | ||
| High Light | smd chip resistor ，pir motion sensor | ||
Φ9.7mm omni-directional electret condenser microphone -40±3dB
Description:
An electret microphone is a type of electrostatic capacitor-based microphone, which eliminates the need for a polarizing power supply by using a permanently charged material. It converts sound into an electrical signal, and are commonly used in telephones, wireless telephones, mobile phones, telephones, PCs, language-learning recorders, radio recorders, cassette recorders, alarms, voice control toys, voice control switches and so on.
The top of an electret capsule is covered with a porous material which is attached with glue. This material keeps dust and other debris away from the sensitive electret material, and also gives some protection from wind noise on the microphone.Underneath this dust cover is a small hole in the aluminum capsule. This is where the sound enters the microphone. The aluminum capsule contains the electret material itself, and a small amplifier.The electret material is made of a metalized mylar film which is adhered to a metal washer. There is also a small red plastic spacer to keep the film a fixed distance from the amplifier module. Both the spacer and electret are extremely thin.
List and structure of material:
| 1 | PCB | FR-1 |
| 2 | FET | K596 |
| 3 | HOLDER | ABS |
| 4 | BACK PLATE | CU |
| 5 | SPACER | MYLAR |
| 6 | FILM | FEP |
| 7 | OUTER MOST SHELL | AL |
| 8 | CLOTH | FABRICS |
Application:
Electret microphones are the most commonly used microphones today. Every cellphone and laptop has one embedded into it, and many studio microphones are also electrets. They can have an extremely wide frequency response (from 10Hz to 30kHz ), and typically cost less than a dollar. They are also very small and quite sensitive.
Specifications:
| Sensitivity(1KHz,0dB=1V/Pa) | -32±3dB ; -34±3dB ;-36±3dB ; -38±3dB ;-40±3dB ;-42±3dB ; -44±3dB |
| Directivity | Omni-directional |
| Impedance | 2.2KΩ Max. |
| Current consumption | 0.5mA Max. |
| Operation voltage | 1.0~10V |
| S/N ratio | 60dB Min. |
| Sensitivity vs voltage | 3dB Max. at VS=2.0V~1.5V |
| Standard test condition | 94dB S.P.L@1KHz VS=2.0V |
| Frequency | 20~16000Hz |
Dimension:(mm)
Schematic diagram:
Handling instruction:
1, Assembly process
• After connector and holder are once disassembled , they should not be re-used.
• Do not touch outer springs directly(except for PCB or proper terminal set at nominal height.
• Do not give any mechanical shocks to the micphone(e.g. dropping to floor)
2, General information
2-1: This microphone shall not be operated or stored in following environment.
• where liquid(water,solvent and so on)splashes.
• where the air has a high concentration of corrosive gas .
• where is too dusty.
• where temperature changes rapidly.
2-2: Frequency response especially in high frequency region is dependent on the structure of enclosure.
Please remove additional acoustic mass or cavity in front of the microphone to the utmost.
2-3:do not put mechanical pressure more than 2 kg to the microphone.
2-4: microphone should not be in state of outgoing packing for a long-term storage.
2-5: all the soldering procedures upon microphone must be complete in a metallic device,the temperature of the soldering irons must be limited as 320℃ and less 3 s ,the operators,the solder fixtures and the soldering irons must be statically grounded under each soldering process.
Company Details
Business Type:
Manufacturer,Exporter
Year Established:
2012
Total Annual:
1000000-2000000
Employee Number:
100~120
Ecer Certification：
Site Member
ANYO is the leading supplier of electronic components. We were established in 2012, based in Ningbo (Close to ShangHai). Before establishment, we were lawful chief representative of EMDAS ELEKTRONIK in Turkey. We always get the qualified products with fast, easy ordering, short delivery tim... ANYO is the leading supplier of electronic components. We were established in 2012, based in Ningbo (Close to ShangHai). Before establishment, we were lawful chief representative of EMDAS ELEKTRONIK in Turkey. We always get the qualified products with fast, easy ordering, short delivery tim...
Get in touch with us
Leave a Message, we will call you back quickly!