China World Technology Medical Equipment Service Group
| Payment Terms | T/T, Western Union,Paypal |
| Delivery Time | 3-5 working days |
| Packaging Details | Carton |
| Product Name | Drager Expiratory Valve New Original PN 8413660 For Savina® Reusable |
| Brand | Drager |
| Part No | 8413660 |
| Application for | Drager Savina® Ventilaotr |
| Condition | Original New |
| Color | Whie |
| Material | Plastic |
| Reusable | yes |
| Valve Type | Expiratory Valve |
| MOQ | One piece |
| Brand Name | Drager |
| Model Number | 8413660 |
View Detail Information
Explore similar products
Mindray ECG Leadwires EL6802A 12-Lead Limb Cable IEC Clip PN0010-30-42903 For
TS-W-D Patient Monitor Accessories GE Ohmeda TruSignal 9 Pin Spo2 Wrap Sensor
CBL 3 Lead ECG Safety Patient Trunk Cable IEC PN M1510A Ref 989803103871 for
M1024254 GE Pediatric Reusable Temperature Probes 400 Series Skin Probe 3m 10ft
Product Specification
| Payment Terms | T/T, Western Union,Paypal | Delivery Time | 3-5 working days |
| Packaging Details | Carton | Product Name | Drager Expiratory Valve New Original PN 8413660 For Savina® Reusable |
| Brand | Drager | Part No | 8413660 |
| Application for | Drager Savina® Ventilaotr | Condition | Original New |
| Color | Whie | Material | Plastic |
| Reusable | yes | Valve Type | Expiratory Valve |
| MOQ | One piece | Brand Name | Drager |
| Model Number | 8413660 | ||
| High Light | Reusable Drager Expiratory Valve ，Savina® Ventilator Drager Expiratory Valve ，PN 8413660 Drager Expiratory Valve | ||
Drager expiratory valve new original PN 8413660
for Savina® reusable
► Brief Introduction of Drager expiratory valve new original PN 8413660 for Savina® reusable
Drager expiratory valve assembly 8413660 consists of the expiratory valve and the return valve . The expiratory valve is a proportional valve used to regulate the pressure in the respiratory system. The check valve works together with the spring valve of the pressure relief valve to prevent pendulum breathing during spontaneous breathing. The expiratory flow sensor measures the expiratory flow according to the measurement principle of hot wire anemometry. The measured flow rate is therefore a mass flow rate (NTPD). The expiratory valve assembly and the expiratory flow sensor can be removed from the Sabina for cleaning.
► Removing the expiratory valve.
1 Remove and empty the water trap container (A).
2 Turn the locking ring (B) as far to the left as possible.
3 Remove the expiratory valve from the connector.
► Disassembling the expiratory valve.
1 Pull the flow sensor sleeve (C) off the expiratory valve.
2 Remove the diaphragm (D).
► Disinfecting the expiratory valve.
NOTE Disinfect the expiratory valve components (valve body, flow sensor sleeve, diaphragm, water trap) only after disassembly.
After cleaning and disinfecting, always dry the expiratory valve using high-temperature steam sterilization at 134°C (273.2°F) to ensure that any remaining liquid inside is completely dry.
► Reusing the expiratory valve.
NOTE Testing devices with high leaks due to damage to the expiratory valve will not detect all damage. Replace the expiratory valve if any of the following damage is present:
– Cracks in plastic parts.
– Torn membrane – Deformed or hardened rubber parts
► Mounting the expiratory valve
WARNING Risk of patient injury Expiratory valves that are damp or have not been reprocessed can impair the operation of the device and endanger the patient. Only use properly reprocessed expiratory valves which have been sufficiently dried.
► Preparing the exhalation valve
1 Install the diaphragm (A) onto the edge of the exhalation valve housing. 2 Ensure that the diaphragm is installed correctly.
3 Install the flow sensor sleeve (B), if removed.
► Inserting the exhalation valve
1 Rotate the locking ring (D) as far to the left as possible.
2 Push the exhalation valve into the accessory.
3 Rotate the locking ring (D) as far to the right as possible until it locks into place.
4 Gently pull on the exhalation valve to ensure it is securely attached.
5 Install the water collection container (C).
► Specification of Drager expiratory valve new original PN 8413660 for Savina® reusable
| Production Name | Drager expiratory valve new original PN 8413660 for Savina® reusable
|
| Brand | Drager |
| Part No | 8413660 |
| Apply for | Drager Savina® Ventilator |
| Reusable or not | Reusable |
| Condition | Original new |
| Color | White |
| Material | Plastic |
Thank you so much for your attention .If you're interested in Drager Expiratory Valve New Original PN 8413660 For Savina® Ventilator Reusable,feel free to contact us .Thank you .
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer,Exporter,Trading Company,Seller
Year Established:
2015
Employee Number:
20~50
Ecer Certification：
Verified Supplier
China World Technology Medical Equipment Service Group is a company engaged in medical equipments/repair parts and accessories products trading company. The company was established in September 2005, has many famous enterprises at home and abroad (such as America USCO company) to establish a long-te... China World Technology Medical Equipment Service Group is a company engaged in medical equipments/repair parts and accessories products trading company. The company was established in September 2005, has many famous enterprises at home and abroad (such as America USCO company) to establish a long-te...
Get in touch with us
Leave a Message, we will call you back quickly!