Shenzhen ECER Network Technology Co., Ltd.
| Description | Pluggable Connector Assemblies RoHS |
| Delivery Time | 25-42 weeks |
| Packaging Details | - |
| Stock | 3600 |
| Brand Name | TE Connectivity |
| Model Number | 2227670-3 |
View Detail Information
Explore similar products
HRS GT17VS-6DS-5CF
Amphenol U10A474240T
HRS GT17V-6DS-SC
Phoenix Contact 1416353
Product Specification
| Description | Pluggable Connector Assemblies RoHS | Delivery Time | 25-42 weeks |
| Packaging Details | - | Stock | 3600 |
| Brand Name | TE Connectivity | Model Number | 2227670-3 |
This specification defines the performance, test, and quality requirements for the zQSFP+ Stacked connector with cage assembly. It is designed to meet electrical, mechanical, and environmental performance standards for demanding applications.
| Specification | Requirement | Procedure |
|---|---|---|
| ELECTRICAL | ||
| Low Level Contact Resistance (LLCR) | For shield and signal contacts: Baseline (Initial) DR 10 m maximum change from initial (Baseline) | EIA-364-23. Max. Open voltage 20mV. Max current 100 mA DC. All contacts to be measured. Measuring points shall be as indicated in Figure 1. |
| Insulation resistance | 1000 M minimum | EIA-364-21. Test voltage 100V DC. Duration: 1 minute. Measure between adjacent contacts. |
| Withstanding voltage | No breakdown or flashover. | EIA-364-20, Condition I. Test voltage: 300 volts AC at sea level. Duration 1 minute. Test between adjacent contacts, signal to signal and signal to ground |
| MECHANICAL | ||
| Random vibration | No contact discontinuity 1 microsecond | EIA-364-28, Test Condition VII, Test Condition Letter D. Subject mated specimens to 3.10 Gs RMS between 20 to 500 Hz. 15 minutes in each of 3 mutually perpendicular planes. |
| Mechanical shock | No contact discontinuity 1 microsecond | EIA-364-27, Test Condition H. Subject mated specimens to 30 Gs half-sine shock pulses of 11 milliseconds duration. Three shocks in each direction applied along 3 mutually perpendicular planes, 18 total shocks. |
| Durability | See Note. | EIA-364-9. Mate and unmate specimens 100 cycles with cage latch operable, Rate: 500 cycles/hour, 10mm/s. |
| Transceiver Mating force | 40 N maximum | EIA-364-13, Method A. Measure force to mate cable plug into zQSFP+Stacked connector including cage. Maximum rate of 12.7mm per minute. |
| Transceiver Unmating force | 30 N minimum | EIA-364-13, Method A. Measure force to unmate cable plug from zQSFP+Stacked connector including cage by pulling at latching release feature. |
| Rotational cable pull | 33.4 N minimum without displacement of cage assembly or connector from PCB. | Load cable module into connector with cage assembly applied to PCB with attached bezel. Rotate cable 40 degrees toward PCB, and then rotate 360 degrees with the load still applied. |
| Press-fit insertion force | Cage individual pin 40N maximum, Conn individual pin 20N maximum | TE Spec 109-41. Measure force necessary to press connector with cage assembly into the PCB at a maximum rate of 12.7 mm [.50 inch] per minute. |
| Press-fit retention force | Cage and connector individual compliant pin 4N minimum | TE Spec 109-30. Measure force necessary to remove connector with cage assembly from the PCB at a maximum rate of 12.7 mm [.50 inch] per minute. |
| Module Retention | No damage to module below90 N | Load cable module into connector with cage assembly applied to PCB with attached bezel. Apply specified axial load to engaged module at a maximum rate of 6.35 mm [.25 inch] per minute and hold 1 minute to very module retention and cag latch strength. |
| Cage latch, axial retention | 125 N minimum. | EIA 364-98. Measure fore necessary to remove zQSFP+ module from cage assembly with latches enabled. |
| Reseating | See note. | Manually unmate and mate specimens. Perform 3 such cycles. |
| ENVIRONMENTAL | ||
| Thermal shock | See Note. | EIA-364-32, Method A, Test Condition I. Subject mated specimens to 10 cycles between -55 and 85C with 30 minute dwells at temperature extremes and 1 minute transition between temperatures. |
| Temperature/ Humidity cycling. | See Note. | EIA-364-31, Method III. Subject mated specimens between 253C at 80% RH and 65C 3C at 50% RH. Ramp times should be 0.50 hour and dwell should be 1.0 hour. Perform 24 such cycles. |
| Temperature life (preconditioning). | See Note. | EIA-364-17, Method A, Test condition 4. Test subject specimens mated to blank transceivers to 105C for 72 hours. |
| Temperature life | See Note. | EIA-364-17, Method A, Test condition 4. Test Subject mated specimens to 105C for 240 hours. |
| Thermal disturbance | See Note. | EIA-364-10, Condition A. Subject mated and board mounted specimens to 10 cycles between 15 3C and 85 3C as measured on the specimen. Ramp times > 2C per minute with dwell times long enough to ensure contacts reach the temperature extremes (5 minutes minimum). Humidity is not controlled. Perform 10 such cycles. |
| Mixed flowing gas. | See Note. | EIA-364-65, Class IIA (4 gas). Subject board mounted specimens to environmental Class IIA for 14 days. One-half of the specimens (receptacle only) unmated for 224 hours followed by 112 hours mated. The remaining one-half of the specimens mated for 14 days. |
| Dust | See Note. | EIA-364-91 Expose unmated connectors to dust contamination. Dust composition: #1. Flow rate: 300 meters/minute. Exposure time: 1 hour |
| RATINGS | ||
| Working Voltage | 30 VDC Maximum | |
| Current Carrying capacity | 0.5 A maximum per contact (Signal application only) | |
| Operating Temperature | -40C to 85C | |
| Non-operating Temperature | -55C to 105C | |
Company Details
Business Type:
Manufacturer
Year Established:
2009
Total Annual:
100000000-20000000
Employee Number:
500~600
Ecer Certification：
Verified Supplier
Shenzhen ECER Network Technology Co., Ltd. is a professional supplier specializing in industrial and power connectors for industrial automation, power systems, electrical equipment, control systems, machinery, and other demanding applications. We focus on providing reliable connector solutions for... Shenzhen ECER Network Technology Co., Ltd. is a professional supplier specializing in industrial and power connectors for industrial automation, power systems, electrical equipment, control systems, machinery, and other demanding applications. We focus on providing reliable connector solutions for...
Get in touch with us
Leave a Message, we will call you back quickly!