RPM Mazda Ford Crankshaft Position Sensor Nissan Altima 490 Ohm ODM

Crankshaft Position Sensor 1318773 For Ford / Mazda

Part number 1318773 is recognized across multiple brands and supplier lines. The following cross-reference numbers are commonly associated with this sensor:

Note: Cross-reference numbers are provided for reference purposes only. Always verify compatibility with your specific vehicle before purchase.

Part number 1318773 is compatible with a broad range of vehicles across multiple manufacturers. The sensor is primarily used in Ford and Mazda applications.

• Ford – Various models

• Mazda – Various models

• – Various models including C70 II Convertible (542) and XC70 II (136)

The Crankshaft Position Sensor is typically located at the rear of the engine block, above the flywheel. It is used to determine engine speed and Top Dead Center (TDC), ensuring precise ignition timing.

Note: Compatibility may vary by specific vehicle configuration, production date, and regional specifications. Always verify fitment for your particular vehicle before purchase.

A failing or malfunctioning crankshaft position sensor can produce a range of noticeable symptoms. Early recognition of these warning signs can prevent more serious engine damage and costly repairs.

The most critical symptom of a failing crankshaft position sensor is the engine's inability to start. The crankshaft position sensor provides the ECU with the information that the engine is showing positive RPM and is ready to start. If the ECU does not receive a signal from the sensor, or the sensor is outputting values that it is not anticipating, the engine will crank but fail to start.

A failing crankshaft position sensor can cause the engine to stall unexpectedly while driving or at idle. The stalling can occur suddenly and without warning, often with the tachometer dropping to zero during the event. In some cases, the engine may restart immediately, while in others it may require a cooling-off period.

When the crankshaft position sensor provides an erratic or incorrect signal, the engine may exhibit a rough or uneven idle. This occurs because the ECU cannot properly synchronize fuel delivery and ignition timing without accurate crankshaft position data.

A failing sensor can cause a noticeable loss of engine power, particularly during acceleration. The engine may feel sluggish or unresponsive when the throttle is applied.

A malfunctioning crankshaft position sensor will typically trigger the Check Engine Light. Common diagnostic trouble codes associated with this sensor include:

• P0335 – Crankshaft Position Sensor "A" Circuit Malfunction

• P0336 – Crankshaft Position Sensor "A" Circuit Range/Performance

• P0339 – Crankshaft Position Sensor "A" Circuit Intermittent

Common causes of crankshaft position sensor failure include:

• Mechanical damage – Physical impact or wear

• Damage to the Encoder Wheel – The trigger wheel or signal plate may be damaged

• Damage to Internal Circuits – Electrical failure within the sensor

• Interruption in connections to the ECU – Wiring issues or loose connections

• Corrosion – Moisture ingress causing terminal corrosion

When purchasing a replacement crankshaft position sensor (Part No. 1318773), consider the following factors to ensure you select the right product for your needs:

Always confirm that the part number on the replacement sensor matches your vehicle's requirements. Part number 1318773 may also be referenced as 1 318 773. Related part numbers in this family include 3M6G6C315BA (Ford) and L81318221A (Mazda). Verify that the sensor you are purchasing carries the correct OE number for your specific vehicle application.

This sensor is vehicle-specific and must be compatible with your engine system. Cross-reference the sensor with your vehicle's:

• Make and model – Primarily Ford, Mazda

• Model year

• Engine configuration

• Production date

Verify that the replacement sensor matches the required specifications:

• Sensor Type: Inductive Sensor

• Resistance: 490 Ohm

• Fitting Depth: 2.5 – 3 mm

• Connecting Angle: 90°

• Number of Poles: 2-pin connector

The crankshaft position sensor is a critical engine management component. Choose a sensor that meets or exceeds OEM specifications for:

• Signal accuracy – Proper pulse generation and amplitude

• Durability – Resistance to heat, vibration, and contamination

• Precision engineering – Exact fit and function matching original specifications

Sensors from reputable brands are tested in-house at state-of-the-art facilities and are built to withstand the demands of the environment with high-quality materials and electronics.

Before replacing the sensor, thoroughly inspect the sensor connector for looseness, poor connections, bending, corrosion, contamination, or damage. In some cases, the issue may be related to the wiring or connector rather than the sensor itself. Check the crankshaft sensor electrical circuits and inspect for damage. If a fault is identified in the sensor circuit, repair the wiring before replacing the sensor.

The crankshaft position sensor is typically located at the rear of the engine block, above the flywheel. Access may require working from underneath the vehicle or removing components for clearance. Consider whether you have the tools and expertise for DIY installation or if professional installation is recommended.

Verify the warranty terms offered with the sensor. Some manufacturers offer up to 2 years warranty on their sensors. A longer warranty period often indicates greater confidence in product quality.

When ordering online, confirm shipping terms and delivery timelines. Ensure the seller uses reputable shipping carriers to protect the sensor during transit. The sensor is relatively compact, with approximate dimensions of 42.3 × 70.1 × 42.0 mm and a net weight of approximately 0.032 kg.