Two Phase Decanter Centrifuge for Electronics Sludge

Metal Finishing & Electronics Sludge Decanter is designed for continuous solid-liquid separation of metal hydroxide sludge, inorganic fine sludge, and heavy-metal-containing wastewater sludge.

For most metal finishing and electronics sludge applications, the recommended configuration is a two-phase decanter centrifuge because the main target is to separate solid sludge from wastewater after neutralization, precipitation, and flocculation.

• Acid pickling sludge dewatering
• Phosphating sludge treatment
• PCB copper-containing sludge dewatering
• Semiconductor CMP wastewater slurry treatment
• PV silicon wafer cutting slurry separation
• Lithium battery material sludge separation
• Rare earth precipitation sludge treatment
• Metal hydroxide sludge dewatering

Typical materials include metal hydroxides, inorganic fine particles, ultra-fine abrasive particles, silicon powder slurry, suspended solids, precipitated sludge, copper-containing sludge, CMP slurry, and industrial wastewater.

• The feed mainly contains solid sludge + liquid wastewater.
• It is suitable for sludge formed after neutralization, precipitation, and flocculation.
• It helps reduce sludge volume and lower disposal cost.

• If the feed contains oil, grease, or organic solvents.
• If the sludge contains extremely abrasive particles.
• If the process requires very high liquid clarity after centrifugation, downstream filtration may be needed.

1. Metal-containing sludge enters the rotating bowl through the feed pipe.
2. Under centrifugal force, heavier metal hydroxides and inorganic particles move outward.
3. The screw conveyor continuously pushes the separated solids toward the discharge end.
4. The clarified liquid phase is discharged through the liquid outlet.
5. The discharged sludge cake is collected for further treatment, stabilization, or disposal.

• Continuous automatic operation
• Suitable for metal hydroxide and inorganic sludge
• Reduced sludge volume
• Lower sludge disposal cost
• Stable separation after flocculation
• Optional anti-corrosion material design
• Optional wear-resistant protection for abrasive sludge
• Compact footprint compared with some traditional dewatering systems

With proper neutralization, precipitation, flocculation, and stable feeding, this decanter centrifuge can typically achieve:

• 75–95% solid capture rate
• 60–90% suspended solids reduction
• 20–40% cake solids content
• 60–80% final cake moisture
• 25–55% sludge volume reduction
• 20–45% lower sludge handling / disposal load
• 16–24 hours/day continuous operation

Actual results depend on sludge composition, particle size, floc strength, pH, chemical dosing, and corrosion or abrasion level.

Is this machine suitable for PCB sludge?

Yes. It can be used for PCB copper-containing sludge after proper chemical precipitation and flocculation.

Is polymer dosing required?

Usually yes. Polymer dosing helps improve floc formation, solid capture, and cake dryness.

What material is recommended?

Depending on corrosion risk, options may include SUS304, SUS316L, duplex stainless steel, or special anti-corrosion material design.

Can it handle abrasive inorganic sludge?

Yes, but wear protection should be selected according to the actual abrasive content and particle hardness.

What information is needed for model selection?

Please provide feed material, capacity, solids content, pH, chloride level, temperature, particle characteristics, target cake moisture, and corrosion or abrasion requirements.

To recommend a suitable model, please share:

• Feed material name
• Capacity requirement
• Solids content
• pH value
• Temperature
• Heavy metal type
• Corrosion condition
• Abrasion condition
• Target cake moisture
• Polymer dosing condition
• Operating hours
• Site voltage or control preference

Our engineering team can suggest a suitable two-phase decanter centrifuge configuration for your metal finishing or electronics sludge dewatering project.

Contact Peony for Partnership

If you have local customer channels or project resources in metal finishing wastewater, PCB sludge, semiconductor CMP slurry, PV silicon wafer cutting slurry, lithium battery material sludge, rare earth precipitation sludge, or heavy metal wastewater treatment, peony welcomes cooperation.

Send us your target market, customer type, project background, and cooperation proposal. Our team will evaluate the opportunity and provide technical and commercial support for suitable projects.