Compression Mold Bathroom Spray Nozzle

Product Introduction

Silicone elastomer nozzles, mainly used in toilet and kitchen facilities, such as shower heads, faucets, etc.Some elastomer nozzles are also used as liquid flow control valves or mouth openers in beverage and cosmetic bottles.A silicone nozzle is a device used at the end of a liquid pipe to control the direction and characteristics of fluid flow (in particular, to increase the flow rate).

Our advantages in silicone rubber shower heads

Product Pictures

The nozzle is placed at the end of the outlet pipe and can be used to direct the flow of water or to change the flow of liquid, usually to control the speed, direction, mass, shape and/or pressure of the fluid, such as the flow.When the flow velocity of the elastomer nozzle increases, the pressure energy consumption also increases.

Material & Structure

The silicone nozzle pad is made of 100% natural silicone resinIn addition, the nozzle can also be made of plastic (PVC, PTFE), steel (stainless steel, brass, copper). and the nozzle exit is usually round, rectangular, triangular or other shapes.Usually round holes are much better than the other two.At the same Reynolds number, because the nozzle of the circular nozzle tends to flow along the center line, it is less likely to produce a second flow.

Silicone nozzles are common in our daily life, such as faucet exit, bathroom shower head, bottle mouth spray.However, different silicone nozzles have different structures, such as thin-wall orifice (a), extended cylinder nozzles (b), inserted cylinder nozzles (c), contraction cone nozzles (D), expansion cone nozzles (E), and streamline nozzle.They are designed to be used in different contexts to meet the initial requirements of the design.

Nozzle cleaning

Over time, silica gel nozzles can accumulate in shower heads, causing a change in flow, with the nozzles spraying water in all directions, or the nozzles becoming clogged with scale, reducing the flow.Then the shower head won't work as well as it used to.At this point, we must perform the necessary treatments to help the shower head return to its previous peak.

1. As some of the stubborn stains are difficult to clean, we have to remove the shower faucet when necessary.

2. Silicone elastomer nozzle cleaning is relatively convenient.The well-designed protruding silicone nozzle makes it easy for you to clean the nozzle by hand or cloth.

3. We can also remove the sprinkler head and soak it in vinegar for half an hour to dissolve the stain and limescale, and then clean it with clean water.

In order to save mold manufacturing costs or lack of experience, some suppliers choose to mill mold steel to form needles to produce silicon shower nozzles. Those are just two or three templates, without any punch pins.

This is not a big problem when making a small number of samples. When mass production starts, you will find that the burrs in the nozzle will gradually increase, which will seriously affect the quality of the nozzle product. This is caused by the wear of the mold after the output increases.

We know that the burrs on the silicone nozzle will affect the function and effect of the nozzle spray, it will change the flow direction of the liquid, and also cause an imbalance in the pressure. Even if there is only one nozzle with quality problems, the entire mold will not be able to function normally.

In fact, the mold tools for rubber shower faucet gaskets are: punching pins, four templates (sometimes five or six templates are needed).

We need to punch holes in the mold to install the punch pins. Moreover, low-speed wire cutting must be selected, even if the low-speed wire cutting process is expensive. (High-speed wire cutting technology cannot meet quality requirements)

When we find burrs on the nozzle of the rubber shower nozzle, we can remove the perforated needle or directly replace it with a new one.

In this way, the quality of each nozzle gasket during mass production can be fully ensured, and production time and maintenance costs of forming molds can also be saved.

We are a professional manufacturer of elastomer silicone nozzle mold and products, can customize for you to fit your elastomer nozzle mold, and can process products, we welcome OEM/ODM orders, you can contact us at any time and get a quotation.