ASTM A106 Gr.B Solid Finned Tube with 11-13Cr Fins For Waste Heat Recovery

Product Specification

ASTM A106 Gr.B Solid Finned Tube with 11-13Cr Fins For Waste Heat Recovery Boilers

An ASTM A106 Gr.B HFW Solid Finned Tube with 11-13Cr Fins is a rugged, engineered heat transfer component that uses a carbon steel body for pressure strength and strategically places chromium-alloy fins where extreme heat and corrosion resistance are required, offering an optimal balance of performance and cost for demanding industrial applications. This tube is designed for extreme service in high-temperature and corrosive environments, typically found in heat recovery systems (e.g., Waste Heat Recovery Boilers - WHRB) and power plants.

Here are some detailed breakdowns:

1. Base Pipe: ASTM A106 GR.B Seamless Pipe

(1). Chemical Composition (Heat Analysis, %)

The composition is designed for high-temperature service, with limits on carbon, manganese, and other elements to ensure weldability, strength, and creep resistance.

(2). Mechanical Properties

These are the guaranteed minimum properties from a tensile test on the finished pipe.

2. Fins Design

(1) Fin Type: HFW Solid Fins

• High-Frequency Welding: This is the process used to attach the fins to the base tube. An electric current at high frequency is used to heat the fin strip and the tube surface precisely, and then pressure is applied to forge-weld them together. This creates a strong, metallurgical bond with minimal heat-affected zone.
• Solid Fins: The fins are notched from a solid strip of metal (in this case, 11-13% Chromium steel) and then welded continuously along their base to the tube. They are not separate pieces mechanically attached (like "L" or "G" fins). This design offers excellent heat transfer efficiency and structural integrity.

(2) Fin’s Material: 11-13Cr

11-13% Chromium is a martensitic stainless steel alloy (similar to grades like AISI 410, 420).

Why it's used for fins:

• High-Temperature Oxidation Resistance: At the high temperatures where the fin tips operate (often 600°C - 750°C+), plain carbon steel fins would rapidly oxidize (scale) and degrade. The chromium forms a protective oxide layer (Cr₂O₃) that drastically slows down further oxidation.
• Corrosion Resistance: Provides good resistance to sulfurous gases (e.g., from flue gas) and other corrosive elements present in exhaust streams.
• Strength at Temperature: Maintains higher strength than carbon steel at elevated temperatures.

3. Why Use This Combination? (Cost vs. Performance)

It's a cost-optimized, high-performance solution:

• Base Tube (A106 Gr.B): Carbon steel is relatively inexpensive and perfectly adequate for containing high-pressure water/steam inside the tube. The internal fluid temperature is lower than the external flue gas temperature.
• Fins (11-13Cr): The fins are exposed to the most aggressive conditions—hot, corrosive flue gas. Using expensive alloy only where it's absolutely needed (the fins) rather than making the entire tube from solid alloy (e.g., ASTM A213 T11) saves significant material cost while delivering the required service life.

Primary Application: High-Temperature Waste Heat Recovery

This component is a core building block in Heat Recovery Steam Generators (HRSGs) and Waste Heat Recovery Boilers (WHRBs) that are exposed to aggressive flue gases. The 11-13Cr fins are the key that unlocks these challenging applications.

Typical Installations:

1. Gas Turbine Exhaust Ducts (HRSGs): In combined cycle power plants, the exhaust from gas turbines is very hot (500-600°C+) and still contains significant oxygen. The 11-13Cr fins resist oxidation ("scaling") in this high-oxygen environment.

• Process Heater & Furnace Stacks: In refineries and petrochemical plants, heaters burning fuel oil or gas produce exhaust with sulfur compounds (SOx). When the tube metal temperature falls below the acid dew point, sulfuric acid can condense. The chromium in the fins provides much better resistance to this low-temperature corrosion compared to carbon steel fins.
• Syngas Coolers & Chemical Process Waste Heat Boilers: In coal gasification or certain chemical processes, the synthesis gas ("syngas") can be highly corrosive. The alloy fins extend the tube bundle's life.
• Biomass & Waste-to-Energy Boilers: Flue gases from burning biomass or municipal waste contain chlorine compounds (HCl) and other corrosive elements. The 11-13Cr fins offer a critical level of protection against chloride-induced corrosion.

Other Applications:

1. Economizers and Heat Exchangers in coal-fired or biomass power plants.

2. Fired Heaters and Process Heaters.