| Payment Terms | L/C,T/T |
| Surface Treatment | Bright/Soap-coated |
| Packing | Spool/Pallet |
| Grade | 304 |
| Supply Ability | >1000 Tons per month |
| Standard | JIS,EN,ASTM,AISI ,DIN,GB |
| Tensile Strength | 550-750N/mm2 |
| Type | Soft |
| Delivery Time | 10-20 days |
| Diameter | 2.8mm |
| Application | Screw |
| Packaging Details | Coil/Spool/Pallet/By customer request |
| Certification | ISO/SGS/RosH |
| Brand Name | TOPONE |
| Place of Origin | China |
| Model Number | 304 |
View Detail Information
Explore similar products
Stainless Scourer Wire 430/304 - Uniform Mesh, 0.15-12mm
Stainless Wire 0.15-12mm, Salt Spray Test Explained
SUS304 Wire 0.15-12mm, Coil Build and Packing
Corrosion Resistant Stainless Wire 0.15-12mm, Annealed
Product Specification
| Payment Terms | L/C,T/T | Surface Treatment | Bright/Soap-coated |
| Packing | Spool/Pallet | Grade | 304 |
| Supply Ability | >1000 Tons per month | Standard | JIS,EN,ASTM,AISI ,DIN,GB |
| Tensile Strength | 550-750N/mm2 | Type | Soft |
| Delivery Time | 10-20 days | Diameter | 2.8mm |
| Application | Screw | Packaging Details | Coil/Spool/Pallet/By customer request |
| Certification | ISO/SGS/RosH | Brand Name | TOPONE |
| Place of Origin | China | Model Number | 304 |
| High Light | Stainless Wire 0.15-12mm ,Stainless Steel Annealed Wire ,Diameter Tolerance Control Wire | ||
Diameter is the one number on a wire purchase order that both sides assume is understood, and it is also the one that causes most disputes. A tolerance band quoted without a measuring method can be met by one instrument and missed by another, on the same coil.
This wire is supplied from 0.15 mm to 12 mm, annealed at 550-750 N/mm2 in 304 and 316L, with three things written into the order before production: the diameter band, the point on the coil where it is checked, and whether out-of-roundness is counted separately.
Tolerance matters differently by process. On a loom it moves the aperture, on a coiler it changes the feed clearance, and on a fastener line it changes the shank diameter after heading. The band should therefore be set from the process, not copied from the previous order.
| Item | Specification |
|---|---|
| Product | Annealed stainless steel wire, diameter controlled |
| Material grade | 304 / 316L |
| Wire diameter | 0.15-12 mm |
| Diameter tolerance | Band agreed per size; typically tighter at the fine end |
| Ovality | Measured on two axes; limit agreed with the band |
| Measuring method | Inline laser gauge plus micrometer check at coil ends |
| Inspection frequency | Continuous inline; sampling at both coil ends before packing |
| Temper | Annealed, soft |
| Tensile strength | 550-750 N/mm2 |
| Surface finish | Bright, or soap-coated for forming |
| Coil weight | 5-250 kg; spool on request |
| Reference standard | ASTM A580 / GB/T 4240 |
| Packing | VCI paper, PP film, wooden pallet |
| MOQ | 500 kg per size |
| Certification | ISO 9001; mill test report 3.1 per EN 10204 |
The opening is the gap between two adjacent wires, so the wire diameter enters the calculation directly. At 0.5 mm wire a 0.02 mm shift is 4% of the diameter, and that percentage carries straight into the open area of the roll.
A coiler, a straightener and a heading die are all set to a clearance around the wire. If the upper limit of the band is wider than the clearance, the wire will not pass, even though every coil is inside the stated band.
Weight per metre follows diameter squared. At the fine end a small band keeps the metre-count per kilogram predictable, which matters when the order is priced by weight and used by length.
A micrometer measures over a defined anvil area and a defined contact force; a laser gauge measures across a shadow. On soft annealed wire, contact force compresses the surface slightly, so the two instruments can read differently on the same wire.
Diameter is measured at both coil ends and inline during drawing, because the ends are where a drifting die shows up first. A single check at the coil start can report a band that the coil end no longer meets.
A wire can sit inside the diameter band on one axis and fall outside it on the other. Measuring two axes at 90 degrees is what separates a round wire from an oval one, and the limit should be stated with the band.
Warp and weft from 0.15 mm to 2 mm, where a narrow band is what allows an aperture to be quoted as a value rather than a range.
Feed rolls and forming pins set to a clearance, where the upper limit of the band is the figure the tooling is actually built around.
Panels and guards from 0.5 mm to 3 mm, where uniform wire diameter keeps the panel flat and the weld pattern even.
Rod grade is verified before drawing. Diameter is measured continuously by inline laser gauge and checked with a micrometer at both coil ends, ovality is measured on two axes, and tensile and elongation are tested per heat per ISO 6892-1. Wire that drifts outside the agreed band is diverted before packing.
Send the diameter band, application and inspection method for technical confirmation and quotation.
Company Details
Business Type:
Manufacturer
Year Established:
1993
Total Annual:
>7000000-8000000
Employee Number:
>1000~2000
Ecer Certification:
Verified Supplier
What We Do As the most reliable and trustworthy factory in the stainless steel wire industry of China, Huayuan Metal manufactures stainless steel wires constant in quality and favorable in price for purchasers all around the world. Our advanced logistics solutions provide a guarantee for ou... What We Do As the most reliable and trustworthy factory in the stainless steel wire industry of China, Huayuan Metal manufactures stainless steel wires constant in quality and favorable in price for purchasers all around the world. Our advanced logistics solutions provide a guarantee for ou...
Get in touch with us
Leave a Message, we will call you back quickly!