Hangzhou Powersonic Equipment Co., Ltd.
| Payment Terms | T/T |
| Supply Ability | 200pcs |
| Packaging Details | carton |
| Material | Titanium |
| Frequency | 40Khz |
| Power supply | 10-100W |
| Raw coating material saving | over 90% |
| Brand Name | RPS-SONIC |
| Model Number | RPS-AT40 |
| Certification | CE |
| Place of Origin | China |
View Detail Information
Explore similar products
40mm Width Ultrasonic Spray Nozzles For Float Glass Coating CCM Production
50Khz Wide Mist Ultrasonic Spray Nozzle For Solar Cell Coating 20nm
Wide Mist 50Khz Ultrasonic Spray Nozzle For Metal Plastic Sheet Coating
Large Area Coating 50Khz Ultrasonic Fogging Nozzles For Semiconductors Coating
Product Specification
| Payment Terms | T/T | Supply Ability | 200pcs |
| Packaging Details | carton | Material | Titanium |
| Frequency | 40Khz | Power supply | 10-100W |
| Raw coating material saving | over 90% | Brand Name | RPS-SONIC |
| Model Number | RPS-AT40 | Certification | CE |
| Place of Origin | China | ||
| High Light | Titanium Ultrasonic Spray Nozzle Systems ，Ultrasonic Atomizing Nozzle Anti Corrosion ，100W Ultrasonic Spray Nozzle Systems | ||
Ultrasonic atomizing flux process introduction Ultrasonic atomizing . The nozzle uses ultrasonic energy to convert the liquid into a fine mist of low-viscosity water droplets. This technology is used in the electronics assembly industry, especially in the application of liquid solder flux for printed circuit assembly, multichip modules (MCM, multichip module), discrete components, ball grid arrays (BGA) and chip scale packaging (CSP), Find a wide range of applications. Low-viscosity spray is a key factor in these applications, because with air or nitrogen, the spray shape can be as small as 0.070" and as large as 18" width depending on the nozzle. Due to this capability, a tiny amount of flux can be applied to components such as BGA, and large printed circuit assemblies can be covered with flux before wave soldering. Because the velocity generated by the ultrasonic nozzle is generally a few inches per second, it is simple to deliver the spray and shape it in a clear, slow-moving air stream. When the spray is directed at the target surface to be coated, the liquid shows a tendency to bounce off the surface and enter the environment.
Description:
Another characteristic of the ultrasonic nozzle is that it can accommodate a wide range of flow rates. Ultrasonic atomization does not require pressure. The speed of liquid atomization is only determined by the speed at which it is introduced into the nozzle. The nozzle can be designed to handle very small conveying speeds, as low as a few milliliters per minute, or relatively large flow rates, up to a few hundred milliliters per minute. Flux spraying Since the early 1990s, ultrasonic nozzles have been successfully used for flux spraying for on-line PCB wave soldering operations, mainly for products such as no-clean, water-soluble, VOC-free and RA (fully activated rosin) Soldering flux. In order to cover the entire board surface with flux, the spray from a static nozzle is conveyed in low-speed air to form a wide, narrow fog band, which is evenly deposited on the bottom surface of the board as the board passes through the spray. The same technique can be used to spray from the top down. Flux spray has advantages over old flux application methods, such as foaming or wave flux. Compared with the old method, flux spray reduces flux consumption by 70%, eliminates the need for flux thinner, provides better process control, and reduces defects. In the past few years, the industry trend has shifted to flux spray
Features
Uniform coating: uniformity >95%
Saving raw materials: raw material utilization rate is over 85%, 4 times that of traditional air spray nozzle
High control accuracy of coating thickness : 20 nm to tens of micron coatings can be precisely sprayed.
Non clogging
Anti-corrosion nozzle
High precision, high controllable spray.
Tech. info:
| Atomized particles | 15-40um |
| Spraying width | 10~50mm |
| Spray flow | >200ML/min |
| Spray height | 30-80mm |
| Suitable for liquid viscosity | <30cps |
| Suspension particle size | <15um |
| Diversion air pressure | <0.05mpa |
Applications
Electronics: Photoresists onto Wafer ,Sensors, PCB Fluxing, Semiconductors etc.
Industrial: Glass, Touch Screen, etc.
Medical: Medical Textile,Stents, Balloon Catheters, Diagnostic Device etc.
Energy: Fuel Cell, Solar Cell, etc.
Company Details
Business Type:
Manufacturer
Year Established:
2010
Total Annual:
500-1000
Employee Number:
100~150
Ecer Certification：
Active Member
R-Responsibility P-Products S-Service sale the right products instead of the expensive one Rps-sonic, consisted with a couple of young people who love ultrasonic very much.The founding members of RPS-SONIC have an average degree of Bachelor's degree or above. They have been in th... R-Responsibility P-Products S-Service sale the right products instead of the expensive one Rps-sonic, consisted with a couple of young people who love ultrasonic very much.The founding members of RPS-SONIC have an average degree of Bachelor's degree or above. They have been in th...
Get in touch with us
Leave a Message, we will call you back quickly!