25mm 40kHz Waterproof Ultrasonic Transducer Sensor for Steam Water Mist Air

DESCRIPTION: Ultrasonic Sensor

MODEL: TM-A2540H12TR

•All specification taken typical at 25C

Closer frequency tolerance,short ringing and wider bandwidth models can be supplied upon request.

units:mm

1. Sound pressure level and sensitivity shall not change by more than 15dB in temperature range of -20°C to 60°C, at a relative humidity of 30%.
2. Sound pressure level and sensitivity shall not change by more than 6dB in the humidity of 10% to 90%, at the temperature of 25° .
3. MOISTURE

   Keep the sensor at 40°C±2°C and 90°C to 95°C R.H for 96±4 hours. Then, release the sensor into the room conditions for 24 hour prior to the measurement. It shall fulfill the specifications in Table 1.

4. VIBRATION

   Subject the sensor to the vibration for 1 hour each in the X.Y and Z axes with the amplitude of 1.5mm at 10 to 55 Hz. It shall fulfill the specifications in Table 1.

5. HIGH TEMPERATURE EXPOSURE

   Subject the sensor to 80±5°C for 24± 1 hours. then, release the sensor into the room conditions for 1 hour prior to the measurement. It shall meet the specifications in Table 1.

6. LOW TEMPERATURE EXPOSURE

   Subject the sensor to -30±5°C for 24± 1 hours. Then release the sensor into the room conditions for 1 hour prior to the measurement. It shall meet the specifications in Table 1.

TABLE 1

1. This sensor is designed for use in air. Do not use this sensor in fluid.
2. In case where this sensor is to be hold in housing, use soft buffer between sensor and housing. The front part of this sensor vibrates in large.



If this part is hold, its characteristics will vary. The top must be free to vibrate.

3. To prevent sensor malfunctions, operational failure or any deterioration of its characteristics, do not use this sensor in the following, or similar conditions.
   • A. In strong shock or vibration.
   • B . In high temperature and humidity for a long time.
   • C. In corrosive gases or sea breeze .
   • D. In an atmosphere of organic solvents. E. In dirty and dusty environments that may contaminate the sensor front.

Tested under 1Vrms Oscillation Level

Tested under 10Vrms @30cm

Tested at 40.0khz frequency

1. Export Control <For customers outside The People's Republic of China>

   No Manorshi products should be used or sold, through any channels, for use in the design, development, production, utilization, maintenance or operation of, or otherwise contribution to

   • ( 1) any weapons (Weapons of Mass Destruction [nuclear, chemical or biological weapons or missiles] or conventional weapons) or
   • (2)goods or systems specially designed or intended for prpfessional end-use or utilization by militar end-uSers.
2. Please contact our sales representatives or product engineers before using the products ir the specification or cataloque for the applications listed below, which require especially high reliability for the prevention of defects which might directly damage a third party's life, body or property, or when one of our products is intended for use in applications other than those specified in this specification.
   • a) Aircraft equipment or Aerospace equipment
   • b) Undersea equipment and Power plant equipment
   • c) Medical equipment and Transportation equipment (vehicles, trains, ships, etc.) d)Traffic signal equipment i Disaster prevention / crime prevention equipment
   • e) Data-processing equipment including Application of similar complexity and/or reliability requirements to the applications listed above
3. Product specifications and catalogues are subiect to change and our products in them ma be discontinued without advance notice.

   Please check with our sales representatives or product engineers before ordering. If there are any questions, please contact our sales representatives or product engineers.

4. Please read rating and CAUTION (for storage, operating, rating, soldering, mounting and handling) in this specifications in order to prevent smoking and/or burning, etc.
5. Please note that unless otherwise specified,we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect of our and/or a third party's intellectual property rights and other related rights in consideration of your use of our products and/or information described or contained in our specifications and cataloques.In thi connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned above under licenses without our consent.
6. No ozone depleting substances(ODS)under the Montreal Protocol are used in our manufacturing process.