Payment Terms | L/C, T/T |
Supply Ability | 300 Piece/Pieces per Month |
Delivery Time | 30DAYS |
Packaging Details | Wooden case or carton case or your requests |
Name | Direct Drive End Cap Static Seal; 1" ID |
Weight | 0.02 kg |
Model | 011043-1 |
Packing | CTN |
Key Selling Points | competitive Price |
Brand Name | WAMIT |
Model Number | 011043-1 |
Certification | CE,ISO |
Place of Origin | CHINA |
View Detail Information
Explore similar products
712101-1 Hyplex Minor Maintenance Kit For 60kpsi Direct Drive Pump
B-1000-2 FLOW 60K water jet intensifier pump LP Cylinder tie rod waterjet pump
007038-3 waterjet parts 60K intensifier high pressure cylinder waterjet pump
B-8346-1 Flow type waterjet 60k ESL electric shift actuator assembly waterjet
Product Specification
Payment Terms | L/C, T/T | Supply Ability | 300 Piece/Pieces per Month |
Delivery Time | 30DAYS | Packaging Details | Wooden case or carton case or your requests |
Name | Direct Drive End Cap Static Seal; 1" ID | Weight | 0.02 kg |
Model | 011043-1 | Packing | CTN |
Key Selling Points | competitive Price | Brand Name | WAMIT |
Model Number | 011043-1 | Certification | CE,ISO |
Place of Origin | CHINA | ||
High Light | 011043-1 Waterjet Pump Parts ,Waterjet Pump Parts static Seals |
011043-1 WaterJet Pump Spare Parts Direct Drive End Cap Static Seal; 1" ID Waterjet Pump Parrts
011043-1 WaterJet Pump Spare Parts Direct Drive End Cap Static Seal; 1" ID Waterjet Pump Parrts descriptions:
Product Name | Direct Drive End Cap Static Seal |
Model Number | 011043-1 |
Brand | WAMIT |
Application | Waterjet direct Drivve Pump |
Size | Standard |
Weight | 0.2kg |
Feature | Long service life |
Condition | New |
Waterjet turbocharger: the sealing principle of the seal:
The purpose of sealing is to set up a perfect physical barrier for a place that may leak and need to be sealed. Static seals are non-leak seals. To achieve this purpose, the seal must have sufficient elasticity to be able to flow (embed) and fill up any unevenness on the sealed surface, while maintaining sufficient rigidity to prevent the system from being fully loaded with sealing pressure Squeeze into the gap between the surfaces. These two requirements have been met for a long time. The elastic flow is formed by compression loading, and the seal is in a stressed state after compression. Thus, the elastic strain stored in the entire sealing system can maintain the contact pressure. Any stress relaxation that may occur in the system will degrade performance. This situation may be caused by stress relaxation of the sealing material itself (which may also be accompanied by creep sliding into the gap), uneven thermal expansion, or in the case of gaskets, due to flange deflection or bolt tension.
All elastic annular seals require that the sealing material has an interference fit with one of the mating parts in the assembled state. For example, in the case of a solid rubber seal ring such as an O-ring or a rectangular ring, the material can be under positive pressure or under tension, or in a partially compressed or partially tensioned state. Similarly, a flexible lip seal can also be under pressure or tension, depending on whether the section is an outer diameter seal or an inner diameter seal.
Therefore, regardless of the structure of the seal, a load will be generated between the sealed contact and the mating surface. The size of this interface load depends on the amount of interference or "compression" caused when assembling the seal and the elastic modulus of the material. In the case of a lip seal, the interface load will vary with the radial thickness of the lip, the length of the flexible leg, and the elastic modulus of the material. The distribution of the interface load is related to the geometry of the cross section, as shown in Figure 1. This load curve shows the general situation of friction and leakage characteristics. For dynamic seals, in order to obtain the dynamic load that causes the seal assembly to move, the friction coefficient must be used to multiply the load caused by the seal. This dynamic load is essentially a power loss.
011043-1 WaterJet Pump Spare Parts Direct Drive End Cap Static Seal; 1" ID Waterjet Pump Parrts:
Our company advantages:
1. Professional water jet equipment supplier engaged in ultra-high pressure water jet equipment research, production, sales, services.
2. Shandong WAMI CNC Technology Co. Cooperates with many famous enterprises in the world.
3.We set up a research center focused on ultra high pressure. We hired technical personals as researchers from foreign and domestic water jet companies. Also we employed researchers in famous colleges and universities to give us technical support.
4.All ultra high pressure waterjet parts(such as,high pressure cylinder ,end bell ,check valve body ,low pressure cylinder ) , warranty is one year or 2000 hours , which one comes from first.if it nature cracked whitin this period, we can change a new (free) for you.
5.Shandong WAMI CNC Technology Co.,is high-tech enterprises,we have CE certificate and ISO 9001.
Company Details
Business Type:
Manufacturer
Year Established:
2014
Total Annual:
500-1000
Employee Number:
10~100
Ecer Certification:
Site Member
SHANDONG WAMI CNC TECHNOLOGY CO.LTD is the professional manufacturer of water jet cutting machine and spare parts for all Chinese brand water jet cutting machine . our factory is located in JINAN city, SHANDONG province, China. we have 420Mpa intensifier pump, 600Mpa intensifier pum... SHANDONG WAMI CNC TECHNOLOGY CO.LTD is the professional manufacturer of water jet cutting machine and spare parts for all Chinese brand water jet cutting machine . our factory is located in JINAN city, SHANDONG province, China. we have 420Mpa intensifier pump, 600Mpa intensifier pum...
Get in touch with us
Leave a Message, we will call you back quickly!