Shenzhen Xinhe'an Technology Co., Ltd.
| Payment Terms | T/T, Western Union |
| Supply Ability | 10000PCS/Month |
| Delivery Time | 3 Working days |
| Packaging Details | 100pcs/carton |
| Product Type | Smoke Alarm |
| Certificaiton | EN54 |
| Adjustable Sensitivity | 1.06±.26%FT |
| Sound Level | ≥90dB |
| Wired | 2 wire |
| Apaitplicon | Fire Secuirty System |
| Specification | D103mm, H55mm |
| Brand Name | XHA |
| Model Number | YT102 |
| Certification | CE |
| Place of Origin | China |
View Detail Information
Explore similar products
2 Wire Conventional Fire Alarm System Wall Mount With Sound And Light Alarm
AC90-270V Fire Alarm Control Panel 4 Zone 8 Zone 16 Zone With Conventional Smoke
Wall / Ceiling Mount Conventional Fire Alarm System With Smoke / Heat Detector
2 Wire Fixed Rate Of Rise Heat Detector ROR For Conventional Safety Fire Alarm
Product Specification
| Payment Terms | T/T, Western Union | Supply Ability | 10000PCS/Month |
| Delivery Time | 3 Working days | Packaging Details | 100pcs/carton |
| Product Type | Smoke Alarm | Certificaiton | EN54 |
| Adjustable Sensitivity | 1.06±.26%FT | Sound Level | ≥90dB |
| Wired | 2 wire | Apaitplicon | Fire Secuirty System |
| Specification | D103mm, H55mm | Brand Name | XHA |
| Model Number | YT102 | Certification | CE |
| Place of Origin | China | ||
| High Light | EN54 2 Wire Smoke Alarm ，CE 2 Wire Smoke Alarm ，OEM 2 Wire Smoke Alarm | ||
EN54 2 Wire Smoke Alarm For Conventional Fire Alarm System
Introduction
The device is photoelectronic detector uses a state of-the-art optical sensing chamber. This detector is designed to provide open area protection and to be used with most conventional fire alarm control panel.
Two LEDs on each detector provide local 360° visible alarm indication. They flash every 3~5 seconds indicating that power is applied and the detector is working properly. The LEDs latch on in alarm. LEDs will be off when a trouble condition exists indicating that the detector sensitivity is outside the listed limit. The alarm can be reset only by a momentary power interruption.
Parameters
| Product Name | Smoke Alarm | Rated operational voltage | 9 to 28VDC Volts Non-polarized |
| Adjustable Sensitivity | 1.06±.26%FT | Static current | ≤40µA @ 24 VDC |
| Alarm current | ≤30mA @ 24 VDC | Work temperature | -10°C~+50°C |
| Certification | EN54 | Humidity | ≤95%. |
| Size | 103*103*55mm | Weight | 155g |
Feature
Conventional Smoke Detector, Operates by Advanced MCU Expert Algorithm Software.
Key Specifications/Special Features
They work perfectly with all conventional intelligent fire control panels
Dual LEDs for 360-degree visibility
Advanced MCU Expert Algorithm Software.
Easy installation and maintenance
Durable sensor head, no need for replacement
SMD circuit board design-satisfactory quality and reliability guaranteed
Installation
IMPORTANT: The detector must be tested and maintained regularly following NFPA 72 requirements. The detector should be cleaned at least once a year.
INSTALLATION
NOTE: All wiring must conform to applicable local codes, ordinances, and regulations.
NOTE: Verify that all detector bases are installed, that the initiating-device circuits have been tested, and that the wiring is correct.
Remove power from initiating-device circuits before installing detectors.
1. Wire the sensor base per the wiring diagram, Figure 1.
2. Install the sensor into the sensor base. Push the sensor into the base while turning it clockwise to secure it in place.
3. After all sensors have been installed, apply power to the control unit.
4. Test the sensor(s) as described in the TESTING section of this manual.
5. Notify the proper authorities that the system is in operation.
Warning:Forbid connect 24VDC directly without current-limiting resistance. Otherwise, the detector would be burnt out.
Product range
Conventional Fire Alarm System
Addressable fire alarm system
Gas Extinguishing control system
Beam Detector
4 wire smoke detectors with relay output.
2 wire Conventional smoke and heat detectors
Explosion-proof flame detector for fire alarm system
Standalone smoke detectors and combustable gas detector
Service
1. OEM &ODM service.
2. Provide technical support and after-sale service.
3. 1 year warranty.
4. Normally 15 working days lead time.
5. Welcome sample order.
Company Details
Year Established:
2001
Total Annual:
4300000-7140000
Employee Number:
40~50
Ecer Certification：
Verified Supplier
We sepecializes in design and manufacture of high quality fire protection solutions for commerical, industrial and domestic applications. we have nearly 20 years experience in the field of fire protection industry.Everlasting desire for innovation drives our company's product development progres... We sepecializes in design and manufacture of high quality fire protection solutions for commerical, industrial and domestic applications. we have nearly 20 years experience in the field of fire protection industry.Everlasting desire for innovation drives our company's product development progres...
Get in touch with us
Leave a Message, we will call you back quickly!