Ecer asks for your consent to use your personal data to:
Personalised advertising and content, advertising and content measurement, audience research and services development
Store and/or access information on a device
Your personal data will be processed and information from your device (cookies, unique identifiers, and other device data) may be stored by, accessed by and shared with 135 TCF vendor(s) and 65 ad partner(s), or used specifically by this site or app.
Some vendors may process your personal data on the basis of legitimate interest, which you can object to by do not consent. Contact our platform customer service, you can also withdraw your consent.
High Gloss 6mm PCD Boring Bit, Anti‑Stick Lathe Internal Boring Tool for 6063 Aluminum, Copper and Brass Alloys
A 6 mm boring bar lives in confined spaces — wristwatch-sized aluminum housings, smartphone chassis bores, graphite mold cavities, thin-wall copper fittings. In these tight geometries, tool chatter, chip packing, and edge degradation aren't inconveniences — they're scrap tickets.
The Palton 6 mm PCD micro boring bar is purpose-built for this territory. A one-piece tungsten carbide shank provides the stiffness. A vacuum-brazed polycrystalline diamond tip provides the cutting endurance. Together, they turn tiny-hole finishing from a process headache into a predictable operation.
Why 6 mm Diameter Matters
At this scale, every micron of tool deflection
writes itself into the bore wall. A conventional steel boring bar at 6 mm diameter flexes under load, especially at deeper reaches. Carbide reduces that flex dramatically. The solid carbide shank on this tool damps vibration at its source — the tool-workpiece interface — rather than transmitting it into the machined surface.
What the operator sees: round bores, straight walls, no waviness in the surface finish, diameter tolerance holding steady from part one to part one thousand.
The Diamond Edge — Aluminum's Antidote
Anyone who has bored aluminum on a production lathe knows the problem: built-up edge. Soft, ductile aluminum welds itself to the cutting tool under heat and pressure, forming a false cutting edge that changes bore diameter unpredictably and tears the surface finish.
PCD solves this at the material level. Its near-zero affinity with aluminum means the chip doesn't stick. Its low friction coefficient means less heat generation to begin with. And its 8,000 HV hardness means the edge stays sharp through high-silicon grades (A390 and similar) that would crater a carbide boring bar within a shift.
Surface Finish Without the Polishing Step
Material
Typical Carbide Finish (Ra)
PCD Micro Bar Finish (Ra)
6061 Aluminum
0.4–0.8 μm
≤ 0.2 μm
ADC12 Die-cast Al
0.6–1.2 μm
0.2–0.4 μm
C110 Copper
0.4–0.8 μm
0.15–0.3 μm
C360 Brass
0.3–0.6 μm
0.1–0.2 μm
CFRP (carbon fiber)
Chipped, fuzzy edge
Clean sheared bore
Mirror-quality internal bores straight off the tool. When a secondary honing or polishing
operation disappears from the process sheet, cycle time compresses and throughput jumps.
Battery tray locating bores, cooling plate internal features
Specification
Parameter
Standard
Customizable
Shank
6 mm solid carbide
2 / 4 / 5 / 8 mm
Tip material
HPHT-sintered PCD
Fine or coarse grain
Nose radius
R0.4 / R0.8
R0.2–R1.2
Overall length
50 / 75 mm
Extended or shortened to drawing
Bonding method
Vacuum brazing + laser edge grinding
Application-specific processes
Tolerance (batch)
±0.005 mm
Tighter on request
MOQ
10 pcs
Trial samples accepted
What
the Shop Gains
No built-up edge on aluminum. The diamond cutting face has no chemical affinity for non-ferrous metals. Chips flow, they don't stick.
Regrindable. PCD tip survives multiple regrinding cycles — lowering the true cost per cutting edge over the tool's full service window.
Heat out, not in. Diamond's thermal conductivity pulls heat into the chip stream. No edge burning, even in dry or MQL setups at high spindle speeds.
Consistent batch performance. Production tolerances controlled to ±0.005 mm across a full batch order, so every tool in the drawer cuts the same bore diameter as the last.
After-Sales & Factory Backing
Stocked 6 mm boring bars ship in 3–7 working days; custom builds in 10–18 working days
Application engineers provide cutting parameters
Company Details
Bronze Gleitlager
,
Bronze Sleeve Bushings
and
Graphite Plugged Bushings
from Quality China Factory
Business Type:
Manufacturer
Year Established:
2016
Total Annual:
1000000-8000000
Employee Number:
50~100
Ecer Certification：
Verified Supplier
Anhui Palton Precision Tools Co., Ltd.
Enterprise core profile
Anhui Palton Precision Tools is a scientific and technological enterprise focusing on the R&D and production of superhard material cutting tools, headquartered in Bozhou, which is committed to providing high-precision cutting...
Anhui Palton Precision Tools Co., Ltd.
Enterprise core profile
Anhui Palton Precision Tools is a scientific and technological enterprise focusing on the R&D and production of superhard material cutting tools, headquartered in Bozhou, which is committed to providing high-precision cutting...
