Beijing Silk Road Enterprise Management Services Co., Ltd.
| Lifetime | 2000hrs@105℃ |
| Operating Temperature | -40℃~+105℃ |
| Capacitance | 2200uF |
| Height - Seated (Max) | 20mm |
| Pin Spacing | 5mm |
| Voltage Rating | 25V |
| Diameter | 13mm |
| Equivalent Series Resistance(ESR) | 300mΩ@100kHz |
| Ripple Current | 2.4A@100kHz |
| Tolerance | ±20% |
| Description | 2200uF 25V Aluminum Electrolytic Capacitors Through Hole,D13xL20mm |
| Mfr. Part # | CD2882281EM1320VFL |
| Package | Through Hole,D13xL20mm |
| Model Number | CD2882281EM1320VFL |
View Detail Information
Explore similar products
High Temperature Aluminum Electrolytic Capacitor Chengx KM228M010G17RR0VH2FP0
V chip Aluminum Electrolytic Capacitors Chengx RVT1E221M0810 Rated 105C with
Aluminum Electrolytic Capacitor Guangdong TOPAZ Elec Tech ECLJ0612270M080P00 for
aluminum electrolytic capacitor HRK 400V10uF CD110 with rated voltage 400 volts
Product Specification
| Lifetime | 2000hrs@105℃ | Operating Temperature | -40℃~+105℃ |
| Capacitance | 2200uF | Height - Seated (Max) | 20mm |
| Pin Spacing | 5mm | Voltage Rating | 25V |
| Diameter | 13mm | Equivalent Series Resistance(ESR) | 300mΩ@100kHz |
| Ripple Current | 2.4A@100kHz | Tolerance | ±20% |
| Description | 2200uF 25V Aluminum Electrolytic Capacitors Through Hole,D13xL20mm | Mfr. Part # | CD2882281EM1320VFL |
| Package | Through Hole,D13xL20mm | Model Number | CD2882281EM1320VFL |
The HRK CD288 series is a high-frequency, low-impedance plugin type aluminum electrolytic capacitor designed for reliable long-term operation. Featuring a green sleeve with gold lettering, these capacitors are suitable for applications requiring stable performance across a wide temperature range. They are manufactured by Shenzhen Hongruikai Electronics Technology Co., Ltd. and adhere to industry standards for quality and environmental compliance.
| Supplier P/N | Capacitance (uF) | Rated Voltage (V) | Capacitance Tolerance (%) | Dissipation Factor (tan, max) (%) | Leakage Current (uA, max) | Surge Voltage (V) | Equivalent Impedance (, 20, 100KHz) | Rated Ripple Current (mA rms, 105, 100KHz) | Durability (Hrs, at 105) | Diameter (mm) | Height (mm) |
|---|---|---|---|---|---|---|---|---|---|---|---|
| CD288 | 2200 | 25 | -20~+20 | 16 | 550 | 32 | 0.30 | 2400 | 2000 | 13 | 20 |
| Item | Test Condition/Method | Judgment Standard |
|---|---|---|
| Capacitance (CAP) | Test circuit: Series equivalent circuit, Test frequency: 120Hz, Test voltage: Rated voltage | Within the error range of rated capacitance (see Table-1) |
| Dissipation Factor (DF) | - | Less than or equal to the dissipation factor tangent value in Table-1 |
| Leakage Current (LC) | Apply rated working voltage across the capacitor and a 100010 resistor in series. Measure leakage current after 2 minutes. | Less than or equal to the leakage current value in Table-1 |
| Surge Voltage | At 15~35, apply surge voltage through a protection resistor (10050)/CR (K). 1000 cycles (charge 305s, discharge 5.50.5min per cycle). | Capacitance change rate: Within 15% of initial value. Dissipation factor: Not greater than specification. Leakage current: Not greater than specification. Appearance: No visible abnormalities. |
| Temperature Characteristics | Stages: 255, -253, -403, 255, +1053 (stabilize at each temperature) | Impedance ratio (Stage 2,3 vs Stage 1): Not exceeding table values. Capacitance change rate (vs Stage 1): Not exceeding 25%. Dissipation factor: Not exceeding 5x specification. Leakage current: Not exceeding specification. |
| Lead Wire Tensile Strength | Apply specified tensile force to leads for 101 sec. | No obvious appearance change, no lead breakage or loosening. |
| Lead Wire Bending Strength | Fix capacitor vertically, apply specified tensile force to leads, rotate 90 in one direction and back, then 90 in the opposite direction and back. | No obvious appearance change, no lead breakage or loosening. |
| Vibration Test | 2 hours per direction on vibration table (total 6 hours). Frequency range: 10~55Hz. Amplitude: 1.5mm. Sweep rate: approx. 1 min/cycle. | Capacitance test: Stable. Capacitance change: Within 5% of initial value. Appearance: No abnormalities. |
| Solderability | Dip terminals in 25% rosin solution for 5-10s, then dip in solder at 2455 to ~1.5-2.0mm from the body. | Over 90% of dipped lead surface area should be covered with fresh tin. |
| Resistance to Soldering Heat | Dip leads below body (1.5-2.0mm) in solder at 2605 (101s) or 35010 (3-4s). Measure after 1-2h at room temp/humidity. | Capacitance change rate: Within 10% of initial value. Dissipation factor: Not greater than specification. Leakage current: Not greater than specification. Appearance: No significant abnormalities. |
| Damp Heat (Steady State) | Place in 405, 90-95% RH environment for 2408 hours. Measure after 1-2h at room temp/humidity. | Capacitance change rate: Within 20% of initial value. Dissipation factor: Not exceeding 1.2x specification. Leakage current: Not greater than specification. Appearance: No significant abnormalities. |
| Rapid Temperature Change | Place in thermal shock chamber. Cycle: +25(3min)-40(30min)+25(3min)+105(30min)+25(3min). 5 cycles. Measure after 1-2h at room temp/humidity. | Capacitance change rate: Within 10% of initial value. Dissipation factor: Not greater than specification. Leakage current: Not greater than specification. Appearance: No significant abnormalities. |
| Endurance | Apply rated voltage and ripple current at upper limit temperature for rated life. Measure after 1-2h in standard environment. | Capacitance change rate: Within 20% of initial value. Dissipation factor: Not exceeding 2x specification. Leakage current: Not greater than specification. Appearance: No significant abnormalities. |
| High Temperature Storage | Place in 1052 environment without voltage for 1000+48/-0 hours. Recover for 16 hours. Measure. | Capacitance change rate: Within 20% of initial value. Dissipation factor: Not exceeding 2x specification. Leakage current: Not greater than specification. Appearance: No significant abnormalities. |
| Anti-explosion | a) AC Test: 0.7x rated voltage or 250V AC (whichever is lower) at 50/60Hz. b) DC Test: 1A DC for diameter 22.4mm; 10A DC for diameter >22.4mm, reverse voltage. | Safety vent opens, no flame. If vent does not open after 30 min, performance is considered satisfactory. |
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Employee Number:
>>300
Ecer Certification：
Verified Supplier
Company Profile Beijing Silk Road Enterprise Management Services Co.,Ltd. is a professional company focus on integrated circuit ic business. Beijing Silk Road will also responsible with exporting and logistic business. there is professional factory Beijing Silk Road which focus on desigining an... Company Profile Beijing Silk Road Enterprise Management Services Co.,Ltd. is a professional company focus on integrated circuit ic business. Beijing Silk Road will also responsible with exporting and logistic business. there is professional factory Beijing Silk Road which focus on desigining an...
Get in touch with us
Leave a Message, we will call you back quickly!