Beijing Silk Road Enterprise Management Services Co., Ltd.
| Operating Temperature | -40℃~+105℃ |
| Capacitance | 220uF |
| Height - Seated (Max) | 16mm |
| Voltage Rating | 63V |
| Diameter | 10mm |
| Tolerance | ±20% |
| Description | 220uF 63V Aluminum Electrolytic Capacitors Through Hole,D10xL16mm |
| Mfr. Part # | RC063M221LO10*16TH-2A1Et |
| Package | Through Hole,D10xL16mm |
| Model Number | RC063M221LO10*16TH-2A1Et |
View Detail Information
Explore similar products
High Temperature Aluminum Electrolytic Capacitor Chengx KM228M010G17RR0VH2FP0
V chip Aluminum Electrolytic Capacitors Chengx RVT1E221M0810 Rated 105C with
Aluminum Electrolytic Capacitor Guangdong TOPAZ Elec Tech ECLJ0612270M080P00 for
aluminum electrolytic capacitor HRK 400V10uF CD110 with rated voltage 400 volts
Product Specification
| Operating Temperature | -40℃~+105℃ | Capacitance | 220uF |
| Height - Seated (Max) | 16mm | Voltage Rating | 63V |
| Diameter | 10mm | Tolerance | ±20% |
| Description | 220uF 63V Aluminum Electrolytic Capacitors Through Hole,D10xL16mm | Mfr. Part # | RC063M221LO10*16TH-2A1Et |
| Package | Through Hole,D10xL16mm | Model Number | RC063M221LO10*16TH-2A1Et |
This specification applies to the BERYL RC Series Radial Aluminum Electrolytic Capacitors (foil type) designed for use in electronic equipment. These capacitors meet IEC 60384 standards and are suitable for applications requiring reliable performance across a wide temperature range.
| Series | Capacitance (uF) | Rated Voltage (WV) | Size (mm) (D x L) | Temperature Range (C) | Capacitance Tolerance | Life (hours) @105C | DF (%)(MAX) @120Hz/20C | LC (A)(MAX) 2min/20C | ESR ()(MAX) @100KHz/25C | Ripple Current (mA rms) (MAX)@105C/100KHz | Surge Voltage (V) |
|---|---|---|---|---|---|---|---|---|---|---|---|
| RC | 220 | 63 | 10 x 16 | -40~+105 | 20% | 3000 | 9 | 139 | 0.20 | 830 | 72 |
| Type | D | P | d | a (L<20) | a (L20) |
|---|---|---|---|---|---|
| 5 | 2 | 0.5 | 1.5 | ||
| 6.3 | 2.5 | 0.5 | 1.5 | ||
| 8 | 3.5 | 0.5/0.6 | 1.5 | ||
| 10 | 5 | 0.6 | 1.5 | ||
| 13 | 5 | 0.6 | 1.5 | ||
| 16 | 7.5 | 0.8 | 2.0 | ||
| 18 | 7.5 | 0.8 | 2.0 | ||
| 22 | 10 | 0.8 | 2.0 |
RC 063 M 221 LO 10*16 TH-2A1 E t
Marking Sample: 220uF RC(M) 2246
-40C to +105C (for 6.3~450WV)
| Item | Performance | Condition | Criteria |
|---|---|---|---|
| 1 | Nominal capacitance (Tolerance) | Measuring Frequency: 120Hz12Hz; Measuring Voltage: Not more than 0.5Vrms +1.5~2.0V.DC; Measuring Temperature: 202 | Shall be within the specified capacitance tolerance. |
| 2 | Leakage current | Connecting the capacitor with a protective resistor (1k10) in series for 2 minutes, and then, measure leakage current. | I (A) 0.01CV or 3 (A) whichever is greater. (C: Capacitance (F), V: Rated DC working voltage (V)) |
| 3 | Dissipation factor | Nominal capacitance, for measuring frequency, voltage and temperature. | Must be within the parameters (See page 3). |
| 4 | Impedance | Measuring frequency: 100kHz; Measuring temperature: 202; Measuring point: 2mm max. from the surface of a sealing rubber on the lead wire. | Must be within the parameters (See page 3). |
| 5 | Load life test | According to IEC60384-4 No. 4.13 methods: Stored at Maximum operating temperature 2C with DC bias voltage plus the rated ripple current for Rated life +48/0 hours. (Sum of DC and ripple peak voltage rated working voltage). Tested after 16 hours recovering time. | Leakage current: Not more than the specified value. Capacitance Change: Within 20% of initial value. Dissipation Factor: Not more than 200% of the specified value. Appearance: No leakage of electrolyte. |
| 6 | Shelf life test | Stored with no voltage applied at Maximum operating temperature 2 for 1000+48/0 hours. Stabilized at room temperature for 16 hours before measurement. | Leakage current: Not more than 200% of the specified value. Capacitance Change: Within 20% of initial value. Dissipation Factor: Not more than 200% of the specified value. Appearance: No leakage of electrolyte. |
| 7 | Maximum permissible (ripple current, temperature coefficient) | Maximum permissible ripple current is the maximum A.C current at 100kHz and can be applied at maximum operating temperature. | Frequency Multipliers provided. Temperature Coefficient factors provided. |
| 8 | Terminal strength | Tensile strength and bending strength of terminals. | No noticeable changes, breakage or looseness at the terminal. |
| 9 | Temperature characteristics | Testing temperatures: 202, -40, 105. Capacitance, DF, and impedance measured at 120Hz. | Specific criteria for capacitance change, dissipation factor, leakage current, and impedance ratio at different temperatures. |
| 10 | Surge test | Applied a surge voltage to the capacitor connected with a (100 50)/CR (k) resistor in series for 305 seconds in every 50.5 minutes at 15~35. Repeated 1000 times. Tested after 1-2 hours under normal humidity. | Leakage current: Not more than the specified value. Capacitance Change: Within 15% of initial value. Dissipation Factor: Not more than the specified value. Appearance: No leakage of electrolyte. |
| 11 | Change of temperature test | Temperature cycle: According to IEC60384-4 No.4.7 methods. 5 cycles of +20 (3 min), Rated low temp (-40 or -25) (302 min), Rated high temp (+105) (302 min). | Leakage current: Not more than the specified value. Dissipation Factor: Not more than the specified value. Appearance: No leakage of electrolyte. |
| 12 | Damp heat test | According to IEC60384-4 No.4.12 methods. Exposed for 5008 hours in an atmosphere of 90~95% RH at 402. | Leakage current: Not more than the specified value. Capacitance Change: Within 10% of initial value. Dissipation Factor: Not more than 120% of the specified value. Appearance: No leakage of electrolyte. |
| 13 | Solderability test | Soldering temperature: 245 5C; Dipping depth: 2mm; Dipping speed: 252.5mm/s; Dipping time: 30.5s. | Soldering wetting time: Less than 3s. Coating quality: A minimum of 95% of the surface being immersed. |
| 14 | Vibration test | Frequency range: 10Hz ~ 55Hz. Peak amplitude: 1.5mm. Sweep rate: 10Hz ~ 55Hz ~ 10Hz in about 1 minute. Applied for 2 hours in each of 3 mutually perpendicular directions. Mounting method: Capacitor with diameter >12.5mm or length >25mm must be fixed with a bracket. | Inner construction: No intermittent contacts, open or short circuiting. No damage of tab terminals or electrodes. Appearance: No mechanical damage in terminal. No leakage of electrolyte or swelling of the case. Markings shall be legible. |
| 15 | Resistance to solder heat test | Terminals immersed into solder bath at 2605 for 101 seconds or 40010 for 3+0/-1 seconds, 1.5~2.0 mm from the body of capacitor. Tested after 1~2 hours under normal temperature and humidity. | Leakage current: Not more than the specified value. Capacitance Change: Within 5% of initial value. Dissipation Factor: Not more than the specified value. Appearance: No leakage of electrolyte. |
| 16 | Vent test | Applies to products with vent (diameter 6.3mm). DC test: Capacitor connected with polarity reversed to a DC power source. Current selected from Table 2 is applied. | The vent shall operate with no dangerous conditions such as flames or dispersion of pieces of the capacitor and/or case. |
Packing Label Marked:
Packing Types: Bulk Packing, Taped Packing, Outer box.
Company Details
Business Type:
Manufacturer,Distributor/Wholesaler,Agent,Importer
Year Established:
2009
Employee Number:
>>300
Ecer Certification：
Verified Supplier
Company Profile Beijing Silk Road Enterprise Management Services Co.,Ltd. is a professional company focus on integrated circuit ic business. Beijing Silk Road will also responsible with exporting and logistic business. there is professional factory Beijing Silk Road which focus on desigining an... Company Profile Beijing Silk Road Enterprise Management Services Co.,Ltd. is a professional company focus on integrated circuit ic business. Beijing Silk Road will also responsible with exporting and logistic business. there is professional factory Beijing Silk Road which focus on desigining an...
Get in touch with us
Leave a Message, we will call you back quickly!