Super Hydraulic Poppet Valve , Hydraulic Control Valve With Solenoid Actuation

Product Specification

2/2, 3/2 and 4/2 directional poppet valve with solenoid actuation

Type M-.SEW6...L3X
Features
- Direct-acting solenoid direction shut-off valve
- Mounting face as per DIN24 340 A
ISO 4401 and CETOP-RP 121H
- Free of leakage
- Switching flexibility in high-pressure state
- Replace the coil, can take pressure operation
- Solenoid coil can rotate for 90 degrees
- Manual emergency operation available
 
Function and configuration
M-SEW6 direction valve is a solenoid shut-off directional poppet valve for control oil opening, stop and flow direction.
Two-position TEE solenoid directional poppet valve consists of valve body (1), Solenoid (2), and valve element (3). Connect a superposition plate below the two-position TEE solenoid directional poppet valve to connect valve body (4), it becomes into two-position four-way direction poppet valve. The manual emergency button (5) can be used to operate the valve when the Solenoid is not powered on.
· M-3SEW6 two-position TEE solenoid directional poppet valve
1). Initial position:
when the Solenoid is not energized, pretention of spring (6) keeps valve element (3) on valve seat (7) on the left, so that oil port P is connected to A and oil port T is closed.
2). Switching position:
after the Solenoid is energized, through angular lever (9) and ball (10), the force of Solenoid (2) acts on push rod (11) of the two-side seal, thus to push valve element (3) and maintain it on right valve seat (8), causing oil port P closed and oil port A connected to port T. Since push rod (11) and valve element (3), acted by the inlet pressure, is in a balance state of axial hydraulic pressure, the valve can be used when pressure is up to 420bar.

 
· M-4SEW6 2-position 4-way solenoid directional poppet valve
1). Initial position:
when the Solenoid is not energized, pretention of spring (6) keeps valve element (12) on valve seat (8) on the right, oil port P is closed and port A connected to T; pressure oil supplied from oil port P push steel ball (13) to valve seat (14), upon which oil port P is connected to B and A connected to T; besides, a control oil line is connected from oil port A acts on the big area of control piston (15), which can be used for unloading to oil tank.
2). Switching position:
after the Solenoid is energized, oil port P is connected to A; pressure oil from the pump goes through the control oil line connected from port A and acts on the big area of control piston (15); steel ball (13) is pushed to the other side of valve seat (14), thus oil port P is connected to A and B connected to T.
 
· Cartridge restriction choke (model M-.SEW6.L3X/.../B...)
To restrict flow through the valve, a restriction choke can be installed.
Restriction choke is installed on port P.
· Cartridge type one-way valve (model M-.SEW6.L3X/.../P)
Cartridge type one-way valve allows oil flow in from port P and it is closed for reverse flowing.
One-way valve installed on port P.

Spool symbols

 
Specification

 
Technical data

 
Electrical data

Note: for electrical connection, protective wire shall be earthed as required.
 
Unit dimensions
·2-position 2-way, 2-position 3-way solenoid directional poppet valve

1 Solenoid
2 Manual emergency button
3 Plug as per DIN43650 (can rotate for 90 degrees)
4 Remove space needed for Solenoid coil.
5 Lock nut, tightening torque MA=4Nm
6 Remove space
7 Name plate.
8. Oil port A and B use O ring 9.25×1.78, P uses O-ring 10×2
9. Valve securing screw: M5×45 GB/T70.1- class 10.9, Tightening torque MA=8.9Nm
    10 2-position 2-way directional valve has oil port A and B which are blind holes;
    3/2 directional poppet valve has oil port A and B which are blind holes.
 
·2-position 4-way solenoid directional poppet valve

1 Solenoid
2 Manual emergency button
3 Plug as per DIN43650 (can rotate for 90 degrees)
4 Remove space needed for Solenoid coil.
5 Lock nut, tightening torque MA=4Nm
6 Remove space
7 Name plate.
8 Connecting valve body
9 Oil port A and B use O ring 9.25×1.78, P uses O-ring 10×2
10 Valve securing screw hole, M5×90 GB/T70.1-10.9, Tightening torque MA=8.9Nm