Microcontroller MCU UART 30MIPS High Performance 16-bit Digital Signal

Product Specification

Microcontroller MCU UART 30MIPS high performance 16-bit digital signal controller chip DSPIC30F2010-30I/SP 

High-Performance Modified RISC CPU:
 • Modified Harvard architecture
 • C compiler optimized instruction set architecture
 • 83 base instructions with flexible addressing 
modes
 • 24-bit wide instructions, 16-bit wide data path
 • 12 Kbytes on-chip Flash program space
 • 512 bytes on-chip data RAM
 • 1 Kbyte nonvolatile data EEPROM 
• 16 x 16-bit working register array
 • Up to 30 MIPs operation:- DC to 40 MHz external clock input- 4 MHz-10 MHz oscillator input with 
PLL active (4x, 8x, 16x)
 • 27 interrupt sources
 • Three external interrupt sources
 • 8 user-selectable priority levels for each interrupt
 • 4 processor exceptions and software traps
 DSP Engine Features:
 • Modulo and Bit-Reversed modes
 • Two 40-bit wide accumulators with optional 
saturation logic
 • 17-bit x 17-bit single-cycle hardware fractional/
 integer multiplier
 • Single-cycle Multiply-Accumulate (MAC) 
operation
 • 40-stage Barrel Shifter
 • Dual data fetch

Peripheral Features:
 • High current sink/source I/O pins: 25 mA/25 mA
 • Three 16-bit timers/counters; optionally pair up 
16-bit timers into 32-bit timer modules
 • Four 16-bit capture input functions
 • Two 16-bit compare/PWM output functions- Dual Compare mode available
 • 3-wire SPI modules (supports 4 Frame modes)
 • I2CTM module supports Multi-Master/Slave mode 
and 7-bit/10-bit addressing
 • Addressable UART modules with FIFO buffers
 Motor Control PWM Module Features:
 • 6 PWM output channels- Complementary or Independent Output 
modes- Edge and Center-Aligned modes
 • 4 duty cycle generators 
• Dedicated time base with 4 modes
 • Programmable output polarity
 • Dead-time control for Complementary mode
 • Manual output control
 • Trigger for synchronized A/D conversions

Quadrature Encoder Interface Module 
Features:
 • Phase A, Phase B and Index Pulse input
 • 16-bit up/down position counter 
• Count direction status
 • Position Measurement (x2 and x4) mode
 • Programmable digital noise filters on inputs
 • Alternate 16-bit Timer/Counter mode
 • Interrupt on position counter rollover/underflow 
Analog Features:
 • 10-bit Analog-to-Digital Converter (ADC) with:- 1 Msps (for 10-bit A/D) conversion rate- Six input channels- Conversion available during Sleep and Idle
 • Programmable Brown-out Reset

 Special Digital Signal Controller 
Features:
 • Enhanced Flash program memory:- 10,000 erase/write cycle (min.) for 
industrial temperature range, 100K (typical)
 • Data EEPROM memory:- 100,000 erase/write cycle (min.) for 
industrial temperature range, 1M (typical)
 • Self-reprogrammable under software control
 • Power-on Reset (POR), Power-up Timer (PWRT) 
and Oscillator Start-up Timer (OST)
 • Flexible Watchdog Timer (WDT) with on-chip low
power RC oscillator for reliable operation
 • Fail-Safe clock monitor operation

 • Detects clock failure and switches to on-chip low
power RC oscillator
 • Programmable code protection
 • In-Circuit Serial Programming™ (ICSP™) 
programming capability
 • Selectable Power Management modes - Sleep, Idle and Alternate Clock modes
 CMOS Technology:
 • Low-power, high-speed Flash technology
 • Wide operating voltage range (2.5V to 5.5V)
 • Industrial and Extended temperature ranges
 • Low power consumption